问

急求ACG1000-A的menuboot.bin，或image或elf

ACG1000

20小时前提问

0关注
0收藏，53浏览

zhiliao_3cONdA

zhiliao_3cONdA 零段

粉丝：0人关注：2人

问题描述：

acg1000-a上电后不能正常启动内核，不能正常ctrl+c进menuboot，一直在uboot。因为早些时候执行过ide write，现在ide尝试各种版本tftp all.bin，然后ide write均不可实现。

U-Boot 2011.03 (Release Version: V3.2.1) (Build time: Jul 22 2014 - 10:22:58) Skipping PCIe port 0 BIST, reset not done. (port not configured) Skipping PCIe port 1 BIST, reset not done. (port not configured) BIST check passed. Warning: Clock descriptor tuple not found in eeprom, using defaults Warning: Board descriptor tuple not found in eeprom, using defaults CUST_MC6100 board revision major:1, minor:0, serial #: mc6100 OCTEON CN6130-AAP pass 1.1, Core clock: 1000 MHz, IO clock: 600 MHz, DDR clock: 533 MHz (1066 Mhz DDR) Base DRAM address used by u-boot: 0x0f800000, size: 0x7fdb80 DRAM: 4 GiB Now running in RAM - U-Boot at: ffffffffc0000000 Clearing DRAM...... done Registered IDE device 0 from IDE bus:dev 0:0 Flash: 4 MiB PCIe: Port 0 is SGMII, skipping. PCIe: Port 1 link active, 1 lanes, speed gen1 PCI console init succeeded, 1 consoles, 1024 bytes each Net: octmgmt0, octmgmt1, octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7 Bus 0: OK Device 0: Model: SM223En-AA Firm: SM223EAD Ser#: (03)5526888-20080228 Type: Hard Disk Capacity: 16383.7 MB = 15.9 GB (33553920 x 512) SATA#0 (No RDY) SATA#1 (3.0 Gbps) USB: USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found Type the command 'usb start' to scan for USB storage devices. Press Ctrl+C to enter menuboot: 3 ** Unable to use ide 0:1 for fatload ** Pointer(20000000) not to ELF data! argv[2]: cOnsole=ttyS0,9600 argv[3]: numcores=4 argv[4]: quiet ## No elf image at address 0x20000000 Octeon cust_mc6100# <INTERRUPT> Octeon cust_mc6100# <INTERRUPT> Octeon cust_mc6100# <INTERRUPT>

组网及组网描述：

无

4 个回答

按时间按赞数

雨下整夜

雨下整夜四段

粉丝：1人关注：8人

现在是什么报错

现在的思路是能有menuboot进不去，也就不存在刷入r6611.bin，因此着手处理menuboot.

zhiliao_3cONdA 发表时间：20小时前 更多>>

现在的思路是能有menuboot进不去，也就不存在刷入r6611.bin，因此着手处理menuboot.

zhiliao_3cONdA 发表时间：20小时前

zhiliao_3cONdA

zhiliao_3cONdA 知了小白

粉丝：0人关注：2人

现在上电直接进uboot了，

U-Boot 2011.03 (Release Version: V3.2.1) (Build time: Jul 22 2014 - 10:22:58)

Skipping PCIe port 0 BIST, reset not done. (port not configured)
Skipping PCIe port 1 BIST, reset not done. (port not configured)
BIST check passed.
Warning: Clock descriptor tuple not found in eeprom, using defaults
Warning: Board descriptor tuple not found in eeprom, using defaults
CUST_MC6100 board revision major:1, minor:0, serial #: mc6100
OCTEON CN6130-AAP pass 1.1, Core clock: 1000 MHz, IO clock: 600 MHz, DDR clock: 533 MHz (1066 Mhz DDR)
Base DRAM address used by u-boot: 0x0f800000, size: 0x7fdb80
DRAM: 4 GiB
Now running in RAM - U-Boot at: ffffffffc0000000
Clearing DRAM...... done
Registered IDE device 0 from IDE bus:dev 0:0
Flash: 4 MiB
PCIe: Port 0 is SGMII, skipping.
PCIe: Port 1 link active, 1 lanes, speed gen1
PCI console init succeeded, 1 consoles, 1024 bytes each

Net: octmgmt0, octmgmt1, octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7
Bus 0: OK
Device 0: Model: SM223En-AA Firm: SM223EAD Ser#: (03)5526888-20080228
Type: Hard Disk
Capacity: 16383.7 MB = 15.9 GB (33553920 x 512)
SATA#0
(No RDY)
SATA#1
(3.0 Gbps)
USB: USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
Type the command 'usb start' to scan for USB storage devices.

Press Ctrl+C to enter menuboot: 0

** Unable to use ide 0:1 for fatload **
Pointer(20000000) not to ELF data!
argv[2]: cOnsole=ttyS0,9600
argv[3]: numcores=4
## No elf image at address 0x20000000
Octeon cust_mc6100#