WAP722E这款ap从v7瘦版本刷到v5版本,后面有次胖版本ap还可以登录。后面再登录console口界面,发现看不到flash,也格式化不了,格式化就报错,提示下面那个。找不到flash刷镜像也刷不了,这是什么问题啊
BootWare password: Not required. Please press Enter to continue.
Password recovery capability is disabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+C: Display Copyright
Ctrl+F: Format File System
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y
Exception Number: 3
Exception Name: TLB exception: store
Exception Instruction: 0x87a35f50
Exception Stack Base: 0x875fb9d8
BootWare Run Address: 0x87a00000
Register contents:
Reg: zero, Val = 0x00000000 ; Reg: at, Val = 0x00000000 ;
Reg: v0, Val = 0x00000000 ; Reg: v1, Val = 0x00000000 ;
Reg: a0, Val = 0x87600e98 ; Reg: a1, Val = 0x0000000c ;
Reg: a2, Val = 0x8761e080 ; Reg: a3, Val = 0x875fba24 ;
Reg: t0, Val = 0x8761e110 ; Reg: t1, Val = 0x00000024 ;
Reg: t2, Val = 0xbf1a0000 ; Reg: t3, Val = 0x000000b4 ;
Reg: t4, Val = 0x000000dc ; Reg: t5, Val = 0xfffffffc ;
Reg: t6, Val = 0x00001a02 ; Reg: t7, Val = 0x00000008 ;
Reg: s0, Val = 0x00000001 ; Reg: s1, Val = 0x87600e98 ;
Reg: s2, Val = 0x00000014 ; Reg: s3, Val = 0x00000100 ;
Reg: s4, Val = 0x87601a98 ; Reg: s5, Val = 0x87601b78 ;
Reg: s6, Val = 0x875fba18 ; Reg: s7, Val = 0x00000100 ;
Reg: t8, Val = 0x00000001 ; Reg: t9, Val = 0x87a3f26c ;
Reg: k0, Val = 0x87b2402c ; Reg: k1, Val = 0x00000000 ;
Reg: gp, Val = 0x87a80c60 ; Reg: sp, Val = 0x875fb9d8 ;
Reg: s8, Val = 0x00000001 ; Reg: ra, Val = 0x87a380e8 ;
Reg: status, Val = 0x10004003 ; Reg: lo, Val = 0x00000000 ;
Reg: hi, Val = 0x00000000 ; Reg: badva, Val = 0x00000004 ;
Reg: cause, Val = 0x4000800c ; Reg: epc, Val = 0x87a35f50 ;
Print call stack:
87a35f50
87a380e8
87a46b9c
87a46d5c
87a2a54c
87a41dcc
87a0d78c
87a0da10
TLB exception: store故障分析报错现象:BootWare 菜单可以正常进入,提示
Note: The current operating device is flash;执行Ctrl+F格式化 Flash,一确认 Y 直接报 Exception Number:3 TLB exception:store,程序崩溃;无法格式化、无法 TFTP 上传镜像,识别不到有效 flash 文件系统。
⚠️ 该 AP 不允许直接 V7 BootWare 刷 V5 镜像;官方流程必须先降级 BootWare 到 V5 版本,再刷 V5 胖镜像,跨大版本不能直接刷系统镜像。
网上有完全一模一样的故障案例,报错寄存器、异常号完全一致,就是 V7 直接刷 V5 胖 AP 导致的砖机现象。
<7> BootWare Operation Menu → 更新 BootWare 程序。注意:如果执行更新 BootWare 时同样报 TLB 异常崩溃,说明扩展 BootWare 区域已经损坏,软件菜单已经无法修复,直接跳到方案 2。
重要:V7 瘦 AP 转 V5 胖 AP 官方标准流程:第一步先刷 V5 的 bootware,第二步再刷 V5 FAT 主镜像,不能直接刷主镜像。
当 BootWare 菜单内做格式化、升级 BootWare 都会触发 TLB 异常崩溃,软件层面已经无法修复,属于 BootWare 扩展段文件系统错乱,只能 SPI 编程器刷写芯片。
Ctrl+F格式化可以正常执行,之后 TFTP 上传 V5 胖 AP 固件即可恢复。风险提示:拆机焊接编程器操作有焊盘损坏风险,没有硬件动手能力建议送修。
编程器写入正确 BootWare 之后,仍然格式化报 TLB 异常;TFTP 写入镜像反复校验失败,则代表 NAND Flash 芯片物理坏块,硬件故障,只能更换 Flash 芯片或者整机返修。
第一次刷完后短暂能登录,只是镜像勉强跑起来,Flash 元数据已经损坏;重启后 BootWare 读取错乱,再次执行擦写操作直接触发 CPU TLB 异常,格式化、刷镜像全部失效。
暂无评论
暂无评论
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论