S5560-54S-EI如何在接口下做端口限速，V7版本，如何清空交换机某一个端口下收发包的命令
- 0关注
- 1收藏，1601浏览
问题描述：
H3C Comware Software, Version 7.1.045, Release 1122
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
H3C S5560-54S-EI uptime is 30 weeks, 3 days, 2 hours, 58 minutes
Last reboot reason : Cold reboot
Boot image: flash:/s5560ei-cmw710-boot-r1122.bin
Boot image version: 7.1.045, Release 1122 Compiled Mar 15 2017 16:00:00
System image: flash:/s5560ei-cmw710-system-r1122.bin System image version: 7.1.045, Release 1122 Compiled Mar 15 2017 16:00:00
Slot 1: Uptime is 30 weeks,3 days,2 hours,58 minutes H3C S5560-54S-EI with 2 Processors
BOARD TYPE: S5560-54S-EI
-------------------------
dis int g 1/0/18 GigabitEthernet1/0/18
Current state: DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: 38ad-be12-c686 Description: GigabitEthernet1/0/18 Interface Bandwidth: 1000000 kbps Loopback is not set Media type is twisted pair Port hardware type is 1000_BASE_T Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 12288 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 16 MDI type: automdix Port link-type: Access Tagged VLANs: None Untagged VLANs: 16 Port priority: 0 Last link flapping: 0 hours 16 minutes 39 seconds Last clearing of counters: Never Peak input rate: 11170506 bytes/sec, at 2013-02-25 05:09:03 Peak output rate: 11851541 bytes/sec, at 2013-02-25 02:39:37 Last 300 second input: 0 packets/sec 0 bytes/sec -% Last 300 second output: 0 packets/sec 0 bytes/sec -% Input (total): 8526192007 packets, 10101144587012 bytes 8525749897 unicasts, 201023 broadcasts, 241087 multicasts, 0 pauses Input (normal): 8526192007 packets, - bytes 8525749897 unicasts, 201023 broadcasts, 241087 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 8768350147 packets, 3254832902037 bytes 8635066965 unicasts, 48776095 broadcasts, 84507087 multicasts, 0 pauses Output (normal): 8768350147 packets, - bytes 8635066965 unicasts, 48776095 broadcasts, 84507087 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier
如何清空某个端口下收发包
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, - overruns, 0 aborts
- ignored, - parity errors Output
(total): 8768350147 packets, 3254832902037 bytes 8635066965 unicasts, 48776095 broadcasts, 84507087 multicasts, 0 pauses
Output (normal): 8768350147 packets, - bytes
8635066965 unicasts, 48776095 broadcasts, 84507087 multicasts, 0 pauses
现在觉得该接口下收发包太多，想清空端口，并对端口做限速
并想对该18号端口做限速，请问配置命令是什么...
int g 1/0/18
- 2019-03-18提问
- 举报
-
(0)
最佳答案
在用户试图：reset counters interface 后面加具体接口 ，可以清空接口计数
如果不加具体接口，那么所有接口计数情况。
可以做端口限速。出方向可以，入方向不行
- 2019-03-18回答
- 评论(2)
- 举报
-
(1)
在接口下配置 qos lr...具体参考他们华三具体产品的配置指导
请问端口限速的命令是什么..
在接口下配置 qos lr...具体参考他们华三具体产品的配置指导
编辑答案
亲~登录后才可以操作哦!
确定你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
- 1. 您举报的内容是什么？（请在邮件中列出您举报的内容和链接地址）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
- 3. 是哪家企业？（营业执照，单位登记证明等证件）
- 4. 您与该企业的关系是？（您是企业法人或被授权人，需提供企业委托授权书）
抄袭了我的内容
×
原文链接或出处
诽谤我
×
- 1. 您举报的内容以及侵犯了您什么权益？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
对根叔社区有害的内容
×
不规范转载
×
举报说明