现在我有一台F1060防火墙,是1g光模块,我感觉好卡,我要看带宽是利用满了,怎样分析
(0)
最佳答案
你的意思是说已经看到接口满了吗?接口满了确实是会卡,是否有可能替换万兆光口呢,或者可以根据你的现网的实际情况通过策略路由来实现分流
(0)
没有办法弄成10G,的我目前是要分析出流量的是不是上现,提供命令或者分析办法
[H3C]dis interface GigabitEthernet 1/0/5 GigabitEthernet1/0/5 Current state: UP Line protocol state: UP Description: GigabitEthernet1/0/5 Interface Bandwidth: 1000000 kbps Maximum transmission unit: 1500 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% Internet address: 10.10.20.10/24 (primary) IP packet frame type: Ethernet II, hardware address: 741f-4a84-8622 IPv6 packet frame type: Ethernet II, hardware address: 741f-4a84-8622 Media type is twisted pair, loopback not set, promiscuous mode not set 1000Mb/s, Full-duplex, link type is autonegotiation Output flow-control is disabled, input flow-control is disabled Last link flapping: 1 days 0 hours 1 minutes Last clearing of counters: Never Current system time:2019-12-05 10:44:41 Last time when physical state changed to up:2019-12-04 10:43:06 Last time when physical state changed to down:2019-12-04 10:43:06 Peak input rate: 18064 bytes/sec, at 2019-11-27 15:27:17 Peak output rate: 18860 bytes/sec, at 2019-11-27 15:27:17 Last 300 second input: 0 packets/sec 11 bytes/sec 0% Last 300 second output: 0 packets/sec 10 bytes/sec 0%
[H3C]interface GigabitEthernet 1/0/5 [H3C-GigabitEthernet1/0/5]f [H3C-GigabitEthernet1/0/5]flow- [H3C-GigabitEthernet1/0/5]flow-control [H3C-GigabitEthernet1/0/5]flow-interval ? INTEGER<5-300> Statistic interval in seconds, in steps of 5 [H3C-GigabitEthernet1/0/5]flow-interval 可以吧接口统计功能改为5秒,然后查看接口的统计数值是不是满了
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
[H3C]interface GigabitEthernet 1/0/5 [H3C-GigabitEthernet1/0/5]f [H3C-GigabitEthernet1/0/5]flow- [H3C-GigabitEthernet1/0/5]flow-control [H3C-GigabitEthernet1/0/5]flow-interval ? INTEGER<5-300> Statistic interval in seconds, in steps of 5 [H3C-GigabitEthernet1/0/5]flow-interval 可以吧接口统计功能改为5秒,然后查看接口的统计数值是不是满了