万兆口插了电口模块,但是学习不到mac
我使用smartbit打流,插光模块的口学习到了mac,但是电口没学习到
使用smartbit打流
(0)
最佳答案
port1/0/27插电口万兆模块(ADOP SFP-10G-LR)
port1/0/28插光口万兆模块(SFP+)
端口正常linkup
[H3C-Ten-GigabitEthernet1/0/28]display interface ten-GigabitEthernet 1/0/27 Ten-GigabitEthernet1/0/27 Current state: DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: 38ad-be04-f7dc Description: Ten-GigabitEthernet1/0/27 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, Port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10240 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 1(default vlan), 100-300 VLAN permitted: 1(default vlan), 100-300 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 1 seconds Last clearing of counters: Never Peak input rate: 117175840 bytes/sec, at 2013-01-17 01:01:22 Peak output rate: 32067392 bytes/sec, at 2013-01-17 00:33:34 Last 300 second input: 61154 packets/sec 93077307 bytes/sec -% Last 300 second output: 0 packets/sec 120 bytes/sec -% Input (total): 54369167 packets, 82610659868 bytes 54367124 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input (normal): 54367085 packets, - bytes 54367124 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input: 2043 input errors, 0 runts, 0 giants, 0 throttles 224 CRC, 1 frame, - overruns, 1818 aborts - ignored, - parity errors Output (total): 19500875 packets, 29591011609 bytes 19492557 unicasts, 0 broadcasts, 8318 multicasts, 0 pauses Output (normal): 19500875 packets, - bytes 19492557 unicasts, 0 broadcasts, 8318 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier
[H3C-Ten-GigabitEthernet1/0/28]display interface ten-GigabitEthernet 1/0/28 Ten-GigabitEthernet1/0/28 Current state: UP Line protocol state: UP IP packet frame type: Ethernet II, hardware address: 38ad-be04-f7dd Description: Ten-GigabitEthernet1/0/28 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is optical fiber, Port hardware type is 10G_BASE_LR_SFP 10Gbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10240 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 1(default vlan), 100-300 VLAN permitted: 1(default vlan), 100-300 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 3 minutes 55 seconds Last clearing of counters: Never Peak input rate: 103362851 bytes/sec, at 2013-01-17 00:44:00 Peak output rate: 11167130 bytes/sec, at 2013-01-17 00:59:52 Last 300 second input: 787 packets/sec 1195751 bytes/sec 0% Last 300 second output: 0 packets/sec 79 bytes/sec 0% Input (total): 67416477 packets, 102338029584 bytes 67375963 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input (normal): 67375963 packets, - bytes 67375963 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input: 40514 input errors, 0 runts, 0 giants, 0 throttles 39864 CRC, 3 frame, - overruns, 647 aborts - ignored, - parity errors Output (total): 3448058 packets, 5213601514 bytes 3439826 unicasts, 0 broadcasts, 8232 multicasts, 0 pauses Output (normal): 3448058 packets, - bytes 3439826 unicasts, 0 broadcasts, 8232 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier
[H3C-Ten-GigabitEthernet1/0/28]display mac-address vlan 102 MAC Address VLAN ID State Port/Nickname Aging 0000-0000-033a 102 Learned XGE1/0/28 Y
(0)
是5130上面插电口模块然后和对端的光口对接吗?还是什么情况?
接口都是正常up的吗?另外这个模块是华三原厂适配的吗?包括模块,如果不适配的能不能正常工作不好说
(0)
这个模块买的时候有确认过适配性吗?感觉是不是不适配啊。端口down肯定是不行的,
display 出来是down的,但是灯是亮的,也闪
这个模块买的时候有确认过适配性吗?感觉是不是不适配啊。端口down肯定是不行的,
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明