hcl模拟器上，irf堆叠后，无法做链路聚合

你好，做irf接口，我只用了xge1/0/49口，其他的口都没有做任何配置

您好，3口是否有其他的配置呢？

<s1>dis link-aggregation v Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing Port: A -- Auto Port Status: S -- Selected, U -- Unselected, I -- Individual Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired Aggregate Interface: Bridge-Aggregation30 Aggregation Mode: Static Loadsharing Type: Shar Port Status Priority Oper-Key -------------------------------------------------------------------------------- GE1/0/2 U 32768 1 GE1/0/3 U 32768 1 GE1/0/20 U 32768 1 GE1/0/21 U 32768 1 GE1/0/22 U 32768 1 试了这几个 都不行 都不能被选中

有可能是因为超规格了，可尝试使用两个物理接口成员试下。

[s1]dis inter g1/0/3 GigabitEthernet1/0/3 Current state: DOWN Line protocol state: DOWN(LAGG) IP packet frame type: Ethernet II, hardware address: 40da-1221-0100 Description: GigabitEthernet1/0/3 Interface Bandwidth: 1000000 kbps Loopback is not set Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 9216 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Access Tagged VLANs: None Untagged VLANs: 1 Port priority: 2 Last link flapping: Never Last clearing of counters: Never Current system time:2020-06-11 13:21:15 Last time when physical state changed to up:- Last time when physical state changed to down:2020-06-11 12:43:41 Peak input rate: 0 bytes/sec, at 00-00-00 00:00:00 Peak output rate: 0 bytes/sec, at 00-00-00 00:00:00 Last 300 second input: 0 packets/sec 0 bytes/sec -% Last 300 second output: 0 packets/sec 0 bytes/sec -% Input (total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input (normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, 0 overruns, 0 aborts 0 ignored, 0 parity errors Output (total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Output (normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Output: 0 output errors, 0 underruns, 0 buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, 0 no carrier 这是3口的显示

我创建一个全新的交换机，没有做任何配置，进行链路聚合没有问题

在原有的交换机使用2个接口做聚合也不可以？

你说的是在已经做好堆叠的机器上吗 ，我之前的报错就是在已经做好堆叠的机器上操作的

您好，就是在原来做好的堆叠的设备上，把链路聚合的配置，成员接口都删掉后，单独使用两个接口，加入聚合组，看下是否能聚合成功。

也不行 试了

如果没有做IRF，就可以对吧？