两台做了堆叠的5600如何进行版本升级?
(0)
最佳答案
l
l
步骤 | 工作内容 |
1 | 先删除配置中关于mad检测的配置 [ASW-T06-I03.CM3]interface Bridge-Aggregation 100 [ASW-T06-I03.CM3-Bridge-Aggregation100]undo mad enable |
2 | 将slot 1设备中的所有业务端口shutdown,并保存配置 [ASW-T06-I03.CM3]interface range Ten-GigabitEthernet 1/0/1 to Ten-GigabitEthernet 1/0/48 [ASW-T06-I03.CM3-if-range]shutdown <ASW-T06-I03.CM3>save The current configuration will be written to the device. Are you sure? [Y/N]:y Please input the file name(*.cfg)[flash:/config.cfg] (To leave the existing filename unchanged, press the enter key): flash:/config.cfg exists, overwrite? [Y/N]:y Validating file. Please wait... Saved the current configuration to mainboard device successfully. Slot 2: Save next configuration file successfully. |
3 | 指定boot-loader,重启升级slot1设备到R2208P01版本;重启完slot 1后立即通过Slot2的Console口,在Slot 2设备上shutdown 所有IRF端口。 <ASW-T06-I03.CM3>boot-loader file flash:/S5820V2_5830V2-CMW710-R2208P01.ipe slot 1 main <ASW-T06-I03.CM3>reboot slot 1 Start to check configuration with next startup configuration file, please wait.........DONE! This command will reboot the specified slot, Continue? [Y/N]:y Now rebooting, please wait... %Jan 3 04:00:55:522 2011 ASW-T06-I03.CM3 DEV/5/BOARD_REBOOT: Board is rebooting on Slot 1. <ASW-T06-I03.CM3>sys [ASW-T06-I03.CM3] interface range FortyGigE 2/0/49 to FortyGigE 2/0/52 [ASW-T06-I03.CM3-if-range]shutdown 注意: 1、 此处千万别reboot错了槽位号,slot 1!切记切记! 需通过console连接到Slot 2上,shutdown IRF端口,该操作要求快速,reboot后立即执行。 |
4 | Console连接到Slot 1设备上,将升级完成后的Slot 1设备中的业务端口全部undo shutdown打开。 [ASW-T06-I03.CM3]interface range Ten-GigabitEthernet 1/0/1 to Ten-GigabitEtherne t 1/0/48 [ASW-T06-I03.CM3-if-range]undo shutdown 注意: 此处切勿保存配置! |
5 | Console连接到Slot 2设备上,指定启动文件为R2208P01,重启slot 2升级版本;、 <ASW-T06-I03.CM3>boot-loader file flash:/S5820V2_5830V2-CMW710-R2208P01.ipe slot 2 main <ASW-T06-I03.CM3>reboot slot 2 Start to check configuration with next startup configuration file, please wait.........DONE! Current configuration may be lost after the reboot, save current configuration? [Y/N]:N This command will reboot the specified slot, Continue? [Y/N]:Y 注意: 此处弹出是否保存配置时,务必选择N |
6 | 查看堆叠是否成功,聚合组状态是否正常,配置是否完整 |
7 | 恢复之前删除的mad检测的配置,并保存配置。 [ASW-T06-I03.CM3]interface Bridge-Aggregation 100 [ASW-T06-I03.CM3-Bridge-Aggregation100] mad enable |
|
|
(0)
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论