H3C WA2620i-AGN由V7降级到V5

1. 从新华三的官网下载对应AP型号的胖版本

https://www.h3c.com/cn/d_201805/1083983_30005_40.htm

下载压缩包WA4300S-CMW520-R1509P01-FAT.zip ，解压生成bin文件，放到电脑桌面上,下载后，需修改文件名，以WA4320为例子，修改对应的启动文件名wa4300s_fat.bin，需要注意文件名称修改正确。

2. 电脑通过网线连接到ap的一个网口

电脑网卡设置为：192.168.0.1 255.255.255.0，如下例子打开TFTP服务器，把bin软件版本放到电脑桌面上，TFTP服务器目录指向电脑桌面，然后点击确定。

3. console口操作刷版本

console口登录方法参考《1.03 设备管理-Console登录方法》

在AP重启的时候按住不停地按Ctrl+B进入设备的bootroom菜单，以下标黑部分为设备自动打印部分。

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extend BootWare

The Extend BootWare is self-decompressing...................................

Done!

按住ctrl+b进到boot

***************************************************************************

*                                                                          *

*                H3C WA4320-ACN-C BootWare, Version 7.07                   *

*                                                                          *

****************************************************************************

Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd.

Compiled Date       : Jul 25 2016

CPU Type            : ATHEROS AR9563

CPU L1 Cache        : 32KB

CPU Clock Speed     : 775MHz

Memory Type         : SDRAM

Memory Size         : 128MB

Memory Speed        : 560MHz

BootWare Size       : 512KB

Flash Size          : 16MB

PCB Version         : Ver.B

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

Password recovery capability is enabled.

Note: The current operating device is flash

Enter < Storage Device Operation > to select device.

3.1、更新扩展bootrom版本

====================================================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Restore to Factory Default Configuration                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Skip Authentication for Console Login                                 |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

===========================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Enter your choice(0-9):

此时按住ctrl+F  格式化flash，“Y”需要手工输入

Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....

............................................................................

..................

Format success.

====================================================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Restore to Factory Default Configuration                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Skip Authentication for Console Login                                 |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

===========================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Enter your choice(0-9): 3    //进入以太网子菜单

====================================================

|Note:the operating device is flash                                        |

|<1> Download Image Program To SDRAM And Run                               |

|<2> Update Main Image File                                                |

|<3> Update Backup Image File                                              |

|<4> Download Files(*.*)                                                   |

|<5> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|                    |

===========================================================================

Enter your choice(0-5): 5    //更改以太网参数

====================================================

|Note:       "." = Clear field.                                            |

|            "-" = Go to previous field.                                   |

|         Ctrl+D = Quit.                                                   |

============================================================================

Protocol (FTP or TFTP) :tftp

//忽略输出内容，直接输入TFTP，然后回车

Load File Name         :wa4300s_fat.bin

//忽略输出内容，直接输入wa4300s_fat.bin，然后回车

Target File Name       :wa4300s_fat.bin

//忽略输出内容，直接输入wa4300s_fat.bin，然后回车

Server IP Address      :192.168.0.1

//忽略输出内容，直接输入电脑主机的 IP，如192.168.0.1，然后回车

Local IP Address       :192.168.0.19

//忽略输出内容，直接输入和电脑主机的ip同一网段，比如192.168.0.19，然后回车

Subnet Mask            :255.255.255.0

//忽略输出内容，直接回车

Gateway IP Address     :0.0.0.0

//忽略输出内容，直接回车

====================================================

|Note:the operating device is flash                                        |

|<1> Download Image Program To SDRAM And Run                               |

|<2> Update Main Image File                                                |

|<3> Update Backup Image File                                              |

|<4> Download Files(*.*)                                                   |

|<5> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|                    |

===========================================================================

Enter your choice(0-5): 1              //此时为更新bootware版本

Loading.....................................................................

............................................................................

............................................................................

.Done.

11248640 bytes downloaded!

Extended BootWare Version is not equal,updating? [Y/N]

Updating Extended BootWare..........Done.

BootWare updated,System is rebooting now.

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extend BootWare

The Extend BootWare is self-decompressing.........................Done!

3.2、升级bin版本

此时bootware版本更新完成，进扩展boot升级设备版本。

****************************************************************************

*                                                                          *

*                H3C WA4320-ACN-C BootWare, Version 1.05                   *

*                                                                          *

****************************************************************************

Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd.

Compiled Date       : Jun 28 2016

CPU Type            : ATHEROS AR9563

CPU L1 Cache        : 32KB

CPU Clock Speed     : 775MHz

Memory Type         : SDRAM

Memory Size         : 128MB

Memory Speed        : 560MHz

BootWare Size       : 512KB

Flash Size          : 16MB

PCB Version         : Ver.B

Read net params from bootrom failed, use the default value

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

Starting to get the main application file--flash:/wa4300s_fit.bin!

The main application file does not exist--flash:/wa4300s_fit.bin!

Starting to get the backup application file--flash:/backup.bin!

The backup application file does not exist--flash:/backup.bin!

Starting to get the secure application file--flash:/secure.bin!

The secure application file does not exist--flash:/secure.bin!

Booting App fails!

Trying to get the IP address from the DHCP server......

Getting IP Address Failed, the system will reboot.

 [State : Idle] Reset request, rebooting the AP

Rebooting......

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extend BootWare

The Extend BootWare is self-decompressing.........................Done!

按住ctrl+b进到boot

****************************************************************************

*                                                                          *

*                H3C WA4320-ACN-C BootWare, Version 1.05                   *

*                                                                          *

****************************************************************************

Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd.

Compiled Date       : Jun 28 2016

CPU Type            : ATHEROS AR9563

CPU L1 Cache        : 32KB

CPU Clock Speed     : 775MHz

Memory Type         : SDRAM

Memory Size         : 128MB

Memory Speed        : 560MHz

BootWare Size       : 512KB

Flash Size          : 16MB

PCB Version         : Ver.B

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.

Note: The current operating device is flash

Enter < Storage Device Operation > to select device.

======================================================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Restore to Factory Default Configuration                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

===========================================================================

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Ctrl+F: Format File System

Enter your choice(0-9):

按住ctrl+F,再次格式化          //第二次格式化，“Y”需要手工输入

Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....

............................................................................

..................

Format success.

======================================================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Restore to Factory Default Configuration                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

===========================================================================

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Ctrl+F: Format File System

Enter your choice(0-9): 3     //进到以太网子菜单

====================================================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|                    |

============================================================================

Enter your choice(0-3): 3      //更改以太网参数

====================================================

|Note:       "." = Clear field.                                            |

|            "-" = Go to previous field.                                   |

|          Ctrl+D = Quit.                                                  |

============================================================================

Protocol (FTP or TFTP) :tftp

//忽略输出内容，直接输入TFTP，然后回车

Load File Name         :wa4300s_fat.bin

//忽略输出内容，直接输入wa4300s_fat.bin，然后回车

Target File Name       :wa4300s_fat.bin

//忽略输出内容，直接输入wa4300s_fat.bin，然后回车

Server IP Address      :192.168.0.1

//忽略输出内容，直接输入电脑主机的 IP，如192.168.0.1，然后回车

Local IP Address       :192.168.0.19

//忽略输出内容，直接输入和电脑主机的ip同一网段，比如192.168.0.19，然后回车

Subnet Mask            :255.255.255.0

//忽略输出内容，直接回车

Gateway IP Address     :0.0.0.0

//忽略输出内容，直接回车

====================================================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|                    |

===========================================================================

Enter your choice(0-3): 2    //更新主应用文件，此时为AP版本文件

Loading.....................................................................

............................................................................

............................................................................

.Done!

11248640 bytes downloaded!

Updating File flash:/wa4300s_fat.bin........................................

............................................................................

..........................................................Done!

====================================================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|                    |

============================================================================

Enter your choice(0-3): 0    //返回主菜单

======================================================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Restore to Factory Default Configuration                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

===========================================================================

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Ctrl+F: Format File System

Enter your choice(0-9): 0              //重启

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extend BootWare

The Extend BootWare is self-decompressing.........................Done!

****************************************************************************

*                                                                          *

*                H3C WA4320-ACN-C BootWare, Version 1.05                   *

*                                                                          *

****************************************************************************

Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd.

Compiled Date       : Jun 28 2016

CPU Type            : ATHEROS AR9563

CPU L1 Cache        : 32KB

CPU Clock Speed     : 775MHz

Memory Type         : SDRAM

Memory Size         : 128MB

Memory Speed        : 560MHz

BootWare Size       : 512KB

Flash Size          : 16MB

PCB Version         : Ver.B

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

Starting to get the main application file--flash:/wa4300s_fat.bin!..........

............................................................................

............................................................................

..........

The App file is self-decompressing..........................................

............................................................................

............................................................................

............................................................................

............................................................................

............................................................................

............................................................................

...........................................................................

.

..................Done!

System application is starting...

Startup configuration file does not exist.

User interface con0 is available.

4. 切换成V5胖模式完成。

重启设备完成后就可以使用默认的管理地址192.168.0.50登录AP进行管理了。登录AP的默认用户名是admin，密码是h3capadmi