• 全部
  • 经验案例
  • 典型配置
  • 技术公告
  • FAQ
  • 漏洞说明
  • 全部
  • 全部
  • 大数据引擎
  • 知了引擎
产品线
搜索
取消
案例类型
发布者
是否解决
是否官方
时间
搜索引擎
匹配模式
高级搜索

利用远程镜像VLAN实现本地镜像支持多目的端口

2020-09-18提问
  • 1关注
  • 2收藏,1576浏览
粉丝:1人 关注:0人

问题描述:

配置如下:

vlan 62 (远程镜像vlan62,目的端口为g1/0/1 g1/0/2 这个vlan只给远程镜像用)

 mirroring-group 1 remote-source 

 mirroring-group 1 remote-probe vlan 62


interface GigabitEthernet1/0/1 

 port access vlan 62 

#

 interface GigabitEthernet1/0/2 

 port access vlan 62

interface GigabitEthernet1/0/7

 port access vlan 330

 mirroring-group 1 mirroring-port both 

interface GigabitEthernet1/0/8 

 port access vlan 330

 mirroring-group 1 mirroring-port both

 #

 interface GigabitEthernet1/0/9 

 port access vlan 330

 mirroring-group 1 mirroring-port both 

#

 interface GigabitEthernet1/0/10 

 port access vlan 330 

 mirroring-group 1 mirroring-port both 

#

 interface GigabitEthernet1/0/11 

 port access vlan 330 

 mirroring-group 1 mirroring-port both 

#

 interface GigabitEthernet1/0/12

 port access vlan 330 

 mirroring-group 1 mirroring-port both


interface GigabitEthernet1/0/30 

 mirroring-group 1 reflector-port



状态:

dis mirroring-group 1

 Mirroring group 1:

 Type: Remote source 

 Status: Active

 Mirroring port: 

 GigabitEthernet1/0/7 Both 

 GigabitEthernet1/0/8 Both

 GigabitEthernet1/0/9 Both 

 GigabitEthernet1/0/10 Both 

 GigabitEthernet1/0/11 Both 

 GigabitEthernet1/0/12 Both 

 Reflector port: GigabitEthernet1/0/30 

 Remote probe VLAN: 62

组网及组网描述:

请问这个配置有问题吗?现在电话录音的反应他们收不到镜像口的部分流量

最佳答案

粉丝:4人 关注:1人

配置没什么问题,不过你把6个千兆口的流量镜像到一个千兆口,这是多打一,镜像目的口出方向带宽有没有占满?拥塞的话会丢包的。

dis int g1/0/1 GigabitEthernet1/0/1 Current state: UP Line protocol state: UP IP packet frame type: Ethernet II, hardware address: 346b-5b0b-e97a Description: GigabitEthernet1/0/1 Interface Bandwidth: 1000000 kbps Loopback is not set Media type is twisted pair Port hardware type is 1000_BASE_T 1000Mbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10240 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 62 MDI type: Automdix Port link-type: Access Tagged VLANs: None Untagged VLANs: 62 Port priority: 0 Last link flapping: 6 weeks 3 days 21 hours 3 minutes Last clearing of counters: Never Peak input rate: 116 bytes/sec, at 2013-01-24 00:31:48 Peak output rate: 618287 bytes/sec, at 2013-01-24 21:28:49 Last 300 second input: 0 packets/sec 10 bytes/sec 0% Last 300 second output: 3 packets/sec 324 bytes/sec 0% Input (total): 129419 packets, 36725187 bytes 4 unicasts, 115348 broadcasts, 14067 multicasts, 0 pauses Input (normal): 129419 packets, - bytes 4 unicasts, 115348 broadcasts, 14067 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 42749365 packets, 7379683358 bytes 25565553 unicasts, 11045166 broadcasts, 6138646 multicasts, 0 pauses Output (normal): 42749365 packets, - bytes 25565553 unicasts, 11045166 broadcasts, 6138646 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier dis int g1/0/2 GigabitEthernet1/0/2 Current state: UP Line protocol state: UP IP packet frame type: Ethernet II, hardware address: 346b-5b0b-e97b Description: GigabitEthernet1/0/2 Interface Bandwidth: 1000000 kbps Loopback is not set Media type is twisted pair Port hardware type is 1000_BASE_T 1000Mbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10240 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 62 MDI type: Automdix Port link-type: Access Tagged VLANs: None Untagged VLANs: 62 Port priority: 0 Last link flapping: 6 weeks 3 days 21 hours 2 minutes Last clearing of counters: Never Peak input rate: 133 bytes/sec, at 2013-01-24 00:25:51 Peak output rate: 618286 bytes/sec, at 2013-01-24 21:28:08 Last 300 second input: 0 packets/sec 9 bytes/sec 0% Last 300 second output: 3 packets/sec 315 bytes/sec 0% Input (total): 199826 packets, 47683914 bytes 5 unicasts, 115146 broadcasts, 84675 multicasts, 0 pauses Input (normal): 199826 packets, - bytes 5 unicasts, 115146 broadcasts, 84675 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 42661434 packets, 7365650481 bytes 25550975 unicasts, 11042915 broadcasts, 6067544 multicasts, 0 pauses Output (normal): 42661434 packets, - bytes 25550975 unicasts, 11042915 broadcasts, 6067544 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier 可以看到它300s流量很小。

zhiliao_wUJrw 发表时间:2020-09-18
回复zhiliao_wUJrw:

是MSTP吗?看一下镜像源端口都在同一颗树里吗?之前见过同芯片的端口不在一棵树里,有的端口被阻塞了,其他端口的流量不能镜像的

你等着 发表时间:2020-09-18

是默认的STP 没起mstp

zhiliao_wUJrw 发表时间:2020-09-18
2 个回答
粉丝:131人 关注:6人

您好,请知:

看配置没什么问题,而且已经是激活的状态。

由于是6个千兆口的流量镜像到一个千兆口,不排除流量过多造成端口打满或拥塞而引起丢包等现象。


zhiliao_tRuPCh 知了小白
粉丝:1人 关注:0人

h3c5120支持这种配置吗?

一般设备只要支持本地镜像的都支持这个

zhiliao_wUJrw 发表时间:2020-10-21

编辑答案

你正在编辑答案

如果你要对问题或其他回答进行点评或询问,请使用评论功能。

分享扩散:

提出建议

    +

亲~登录后才可以操作哦!

确定

亲~检测到您登陆的账号未在http://hclhub.h3c.com进行注册

注册后可访问此模块

跳转hclhub

你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作

举报

×

侵犯我的权益 >
对根叔社区有害的内容 >
辱骂、歧视、挑衅等(不友善)

侵犯我的权益

×

泄露了我的隐私 >
侵犯了我企业的权益 >
抄袭了我的内容 >
诽谤我 >
辱骂、歧视、挑衅等(不友善)
骚扰我

泄露了我的隐私

×

您好,当您发现根叔知了上有泄漏您隐私的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到pub.zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您认为哪些内容泄露了您的隐私?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)

侵犯了我企业的权益

×

您好,当您发现根叔知了上有关于您企业的造谣与诽谤、商业侵权等内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到 pub.zhiliao@h3c.com 邮箱,我们会在审核后尽快给您答复。
  • 1. 您举报的内容是什么?(请在邮件中列出您举报的内容和链接地址)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
  • 3. 是哪家企业?(营业执照,单位登记证明等证件)
  • 4. 您与该企业的关系是?(您是企业法人或被授权人,需提供企业委托授权书)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

抄袭了我的内容

×

原文链接或出处

诽谤我

×

您好,当您发现根叔知了上有诽谤您的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到pub.zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您举报的内容以及侵犯了您什么权益?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

对根叔社区有害的内容

×

垃圾广告信息
色情、暴力、血腥等违反法律法规的内容
政治敏感
不规范转载 >
辱骂、歧视、挑衅等(不友善)
骚扰我
诱导投票

不规范转载

×

举报说明