f1005防火墙用ipsec主模式对接云上，有没有详细配置案例，谢谢

3.2  总部侧创建IPSEC兴趣流匹配到分部的数据

#创建IPSEC的感兴趣流，用于匹配IPSEC数据。

<H3C>system-view

[H3C]acl advanced 3999

[H3C-acl-ipv4-adv-3999]rule permit ip source 192.168.10.0 0.0.0.255 destination 192.168.20.0 0.0.0.255

[H3C-acl-ipv4-adv-3999]quit

#创建acl 3888调用在外网接口用于排除IPSEC兴趣流不做NAT。

[H3C]acl advanced 3888

[H3C-acl-ipv4-adv-3888]rule deny ip source 192.168.10.0 0.0.0.255 destination 192.168.20.0 0.0.0.255

[H3C-acl-ipv4-adv-3888]rule permit ip source any

[H3C-acl-ipv4-adv-3888]quit

3.3  总部侧创建IPSEC安全提议

#加密类型设置为aes-cbc-128，认证类型设置为sha1。

[H3C]ipsec transform-set 1

[H3C-ipsec-transform-set-1]esp encryption-algorithm aes-cbc-128

[H3C-ipsec-transform-set-1]esp authentication-algorithm sha1

[H3C-ipsec-transform-set-1]quit

3.4  总部侧创建IKE安全提议

#IKE安全提议默认的认证类型为sha1，加密类型为DES-CBC，DH组为DH1，所以不需要配置也存在这些参数。

[H3C]ike proposal 1

[H3C-ike-proposal-1]quit

3.5  总部侧创建IKE安全密钥

#创建IKE密钥，地址填写分部侧设备的公网IP，密码设置为123456。

[H3C]ike keychain 1

[H3C-ike-keychain-1]pre-shared-key address 198.76.26.90 key simple 123456

[H3C-ike-keychain-1]quit

3.6  总部侧创建IKE安全框架

#创建IKE安全框架，将本端地址、对端地址、keychain、proposal关联起来。

[H3C]ike profile 1

[H3C-ike-profile-1]keychain 1

[H3C-ike-profile-1]local-identity address 101.88.26.34

[H3C-ike-profile-1]match remote identity address 198.76.26.90

[H3C-ike-profile-1]proposal 1

[H3C-ike-profile-1]quit

3.7  总部侧创建IPSEC安全策略

#创建IKE安全策略GE1/0/3将transform-set、acl、ike-profile、本端地址、对端地址关联起来。

[H3C]ipsec policy GE1/0/3 1 isakmp

[H3C-ipsec-policy-isakmp-GE1/0/3-1]transform-set 1

[H3C-ipsec-policy-isakmp-GE1/0/3-1]security acl 3999

[H3C-ipsec-policy-isakmp-GE1/0/3-1]local-address 101.88.26.34

[H3C-ipsec-policy-isakmp-GE1/0/3-1]remote-address 198.76.26.90

[H3C-ipsec-policy-isakmp-GE1/0/3-1]ike-profile 1

[H3C-ipsec-policy-isakmp-GE1/0/3-1]quit

3.8  总部侧外网接口调用IPSEC策略和NAT动态转换策略

[H3C]interface GigabitEthernet 1/0/3

[H3C-GigabitEthernet1/0/3]ipsec apply policy GE1/0/3

[H3C-GigabitEthernet1/0/3]nat outbound 3888

[H3C-GigabitEthernet1/0/3]quit

3.9  总部侧配置安全策略放通IPSEC数据

#创建对象组，组名称为192.168.10.0

[H3C]object-group ip address 192.168.10.0

[H3C-obj-grp-ip-192.168.10.0]0 network subnet 192.168.10.0 255.255.255.0

[H3C-obj-grp-ip-192.168.10.0]quit

#创建对象组，名称为192.168.20.0

[H3C]object-group ip address 192.168.20.0

[H3C-obj-grp-ip-192.168.20.0]0 network subnet 192.168.20.0 255.255.255.0

[H3C-obj-grp-ip-192.168.20.0]quit

#创建对象策略，策略名称为Untrust-Trust

[H3C]object-policy ip Untrust-Trust

[H3C-object-policy-ip- Untrust-Trust] rule 0 pass source-ip 192.168.20.0 destination-ip 192.168.10.0

[H3C-object-policy-ip- Untrust-Trust]quit

#创建Untrust到Tust域的域间策略调用Untrust-Trust策略

[H3C]zone-pair security source Untrust destination Trust

[H3C-zone-pair-security-Untrust-Trust]object-policy apply ip Untrust-Trust

[H3C-zone-pair-security-Untrust-Trust]quit

3.10  总部侧配置安全策略，放通Untrust到Local，以及Local到Utrust的策略，用于建立IPSEC 隧道

#创建对象策略，策略名称为Untrust-Local

[H3C]object-policy ip Untrust-Local

[H3C-object-policy-ip-Untrust-Local] rule 0 pass

[H3C-object-policy-ip-Untrust-Local]quit

#创建Untrust到Local域的域间策略调用Untrust- Local策略

[H3C]zone-pair security source Untrust destination Local

[H3C-zone-pair-security-Untrust-Local]object-policy apply ip Untrust-Local

[H3C-zone-pair-security-Untrust-Local]quit

#创建对象策略，策略名称为Local-Untrust

[H3C]object-policy ip Local-Untrust

[H3C-object-policy-ip-Local-Untrust] rule 0 pass

[H3C-object-policy-ip-Local-Untrust]quit

#创建Local到Untrust域的域间策略调用Local-Untrust策略

[H3C]zone-pair security source Local destination Untrust

[H3C-zone-pair-security-Local-Untrust]object-policy apply ip Local-Untrust

[H3C-zone-pair-security-Local-Untrust]quit

3.11  分部侧IPSEC配置方法

#与总部侧配置基本相同，IPSEC感兴趣流需要取反配置。

3.12  保存配置

[H3C]save force