本手册适用于如下产品:终结者本体WT828-Q。
传版本只能连接到WT828-Q的上行口g1/0/1~g1/0/4接口(其中g1/0/1、g1/0/2是光口,g1/0/3和g1/0/4是电口),如下图,本实验以电口传版本为例。
操作风险提示:设备有风险,操作不当或者意外断电会导致设备故障,操作需谨慎。升级完成后AP需要重新获取新版本上线,期间可能涉及到一定的窗口时间,请预留充足的时间。
命令行升级需在PC上搭建TFTP Server(推荐用户使用3CDaemon搭建TFTP服务器),注意需要关闭终端的防火墙和无线网卡。
将软件版本下载到设备FLASH内,然后通过命令行加载主机软件版本,加载时输入的文件名一定要一致,建议复制黏贴,然后升级过程中避免断电重启操作。
具体操作如下:
1. 从新华三的官网下载对应设备型号的版本。
版本下载位置在新华三官网(www.h3c.com,cn)产品支持与服务>文档与软件>软件下载>无线>MSG系列多业务网关>MSG300系列云网关
注意!由于WT找不到AC会频繁重启,为避免传版本的时候设备重启,可以输入如下命令,不让WT重启。
<H3C>sys //进入系统视图
[H3C]probe //进入probe视图
[H3C-probe]wlan system internal reboot-restrain //关闭AP 10分钟重启机制
2. 电脑网卡设置为:192.168.10.5/255.255.255.0 ,如下例子打开TFTP服务器,把软件版本WT828Q-CMW710-R2450P01.ipe放到电脑桌面上,TFTP服务器目录指向电脑桌面,然后点击确定。
3. 如电脑和设备已经网络可达,此步可忽略;
创建设备的ip地址,地址为192.168.10.2 255.255.255.0,和电脑同一个网段,保证电脑和设备网络可达。以下标黑部分为设备自动打印部分,标红加粗的命令是需要手动输入。
<H3C> system //进入系统视图
[H3C] interface vlan 1 //进入vlan1虚接口配置视图
[H3C-Vlan-interface1] ip address 192.168.10.2 255.255.255.0 //配置接口ip地址
[H3C-Vlan-interface1] quit //退出到当前视图
4. 通过TFTP上传WT828Q-CMW710-R2450P01.ipe到WT828-Q上,192.168.10.5是电脑的ip。
<H3C> copy tftp://192.168.10.5/WT828Q-CMW710-R2450P01.ipe . //上传版本
//ipe后面空格有个.
Copy tftp://192.168.10.5/WT828Q-CMW710-R2450P01.ipe to flash:/WT828Q-CMW710-R2450P01.ipe? [Y/N]:y
Copying file tftp://192.168.10.5/WT828Q-CMW710-R2450P01.ipe to flash:/WT828Q-CMW710-R2450P01.ipe............................................................................................................................................... Done.
3CD侧可以看到传输的字节:
加载主机软件:
<H3C>boot-loader file flash:/WT828Q-CMW710-R2450P01.ipe main //加载版本
Verifying the file flash:/WT828Q-CMW710-R2450P01.ipe on the device....Done.
H3C WT828-Q images in IPE:
wt828q-boot.bin
wt828q-system.bin
This command will set the main startup software images. Please do not reboot the device during the upgrade. Continue? [Y/N]:y
Add images to the device.
File flash:/wt828q-boot.bin already exists on the device.
File flash:/wt828q-system.bin already exists on the device.
Overwrite the existing files? [Y/N]:y
Decompressing file wt828q-boot.bin to flash:/wt828q-boot.bin.........Done.
Decompressing file wt828q-system.bin to flash:/wt828q-system.bin.............................Done.
Verifying the file flash:/wt828q-boot.bin on the device...Done.
Verifying the file flash:/wt828q-system.bin on the device..........Done.
The images that have passed all examinations will be used as the main startup software images at the next reboot on the device.
Decompression completed.
You are recommended to delete the .ipe file after you set startup software images for all slots.
Do you want to delete flash:/WT828Q-CMW710-R2450P01.ipe now? [Y/N]:y
<H3C>reboot //重启设备
重启完成后,登陆设备查看版本是否升级成功,命令行下通过命令<H3C>display version查看当前版本。
<H3C>dis version //查看当前版本
H3C Comware Software, Version 7.1.064, Release 2450P01
Copyright (c) 2004-2021 New H3C Technologies Co., Ltd. All rights reserved.
H3C WT828-Q uptime is 0 weeks, 0 days, 0 hours, 1 minute
Last reboot reason : Power on
Boot image: flash:/wt828q-boot.bin
Boot image version: 7.1.064, Release 2450P01
Compiled Dec 14 2021 16:00:00
System image: flash:/wt828q-system.bin
System image version: 7.1.064, Release 2450P01
Compiled Dec 14 2021 16:00:00
with 1 800MHz Processor
512M bytes DDR3
128M bytes NandFlash Memory
Hardware Version is Ver.D
CPLD Version is 006
Basic Bootrom Version is 1.08
Extend Bootrom Version is 1.08
[Subslot 0]WT828-Q Hardware Version is Ver.D
版本
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作