某局点现场一台V7的WA4320H-ACN设备,由于现有的AC设备上的license数量不足,需要将AP切换为胖AP使用。了解现场工程师的需求后,我们立即查找相应的资料并查找解决方法。经过查找资料确认该型号的AP胖版本只有V5的版本,所以需要将V7的瘦版本降级为V5的胖版本。
经过查找官网软件版本后确认,该型号的AP仅有V5的胖版本
该型号V7版本的瘦AP经过查阅资料确认,没有可以使用的V7的相应的适配胖版本,和现场工程师协商建议其将该AP降级为V5的胖AP。
引导工程师做V7瘦版本降级V5胖版本的操作,操作过程如下:
在AP的启动过程中
按下Ctrl+B进入AP的BOOTROM菜单
***************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 7.09 *
* *
**************************************************************************
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : Mar 21 2017
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : DDR2 SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 128MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Contro |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==================
|Note: &#39;.&#39; = Clear field. |
| &#39;-&#39; = Go to previous field |
| Ctrl+D = Quit. |
====================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300-boot.bin
:wa4300_fat.bin //用来降boot版本
Target File Name :wa43000-boot.bin
:wa4300_fat.bin
Server IP Address :1.1.1.1
Local IP Address :1.1.1.10
Subnet Mask :0.0.0.0 255.255.255.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Loading.....................................................................
............................................................................
........Done.
7715840 bytes downloaded!
The image is self-decompressing.............................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
...........................................................................
Done.
Extended BootWare Version is not equal,updating? [Y/N] //此处开始boot版本替换
Updating Extended BootWare..........Done.
BootWare updated,System is rebooting now.
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..............................Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 1.15 *
* *
****************************************************************************
Copyright (c) 2004-2015 Hangzhou H3C Technologies Co., Ltd.
Compiled Date : Nov 18 2015
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 32MB
PCB Version : Ver.B
Read net params from bootrom failed, use the default value
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Ctrl+F: Format File System //执行Ctrl+F格式化操作
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
..................
Format success. //格式化成功
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Ctrl+F: Format File System
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>===================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
======================================================================
Enter your choice(0-3): 3
==========================<ETHERNET PARAMETER SET>====================
|Note: &#39;.&#39; = Clear field. |
| &#39;-&#39; = Go to previous field. |
| Ctrl+D = Quit. |
======================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300-boot.bin
:wa4300_fat.bin //替换系统版本为胖版本
Target File Name :wa43000-boot.bin
:wa4300_fat.bin
Server IP Address :1.1.1.1
Local IP Address :1.1.1.10
Subnet Mask :0.0.0.0 255.255.255.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>====================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
======================================================================
Enter your choice(0-3): 2
Loading.....................................................................
............................................................................
........Done!
7715840 bytes downloaded!
Updating File flash:/wa4300_fit.bin.........................................
............................................................................
..Done!
==========================<Enter Ethernet SubMenu>====================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
======================================================================
Enter your choice(0-3): 0
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Ctrl+F: Format File System
Enter your choice(0-9): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..............................Done!
****************************************************************************
* *
* H3C WA4320H-ACN BootWare, Version 1.15 *
* *
****************************************************************************
Copyright (c) 2004-2015 Hangzhou H3C Technologies Co., Ltd.
Compiled Date : Nov 18 2015
CPU Type : ATHEROS AR9557
CPU L1 Cache : 32KB
CPU Clock Speed : 720MHz
Memory Type : SDRAM
Memory Size : 256MB
Memory Speed : 560MHz
BootWare Size : 512KB
Flash Size : 32MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Starting to get the main application file--flash:/wa4300_fit.bin!...........
............................................................................
...............................
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
...............Done!
System application is starting...
Startup configuration file does not exist.
User interface con0 is available.
Press ENTER to get started.
<WA4320H-ACN>
#Jan 23 21:03:12:213 2018 WA4320H-ACN SHELL/4/LOGIN:
Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1<hh3cLogIn>: login from Console
%Jan 23 21:03:12:213 2018 WA4320H-ACN SHELL/5/SHELL_LOGIN: Console logged in from con0.
<WA4320H-ACN>
<WA4320H-ACN>sys
System View: return to User View with Ctrl+Z.
[WA4320H-ACN]
[WA4320H-ACN]
[WA4320H-ACN]
[WA4320H-ACN]dis cu
#
version 5.20, Release 1508P11 //版本替换成功
#
sysname WA4320H-ACN
#
在对V7的瘦AP降级为V5的胖AP的过程中需要使用v5的相应产品的胖版本进行两次版本引导操作,其中第一次用来将boot版本降为V5的,第二次用来将系统版本替换为相应的V5胖版本。
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作