WX5004下挂5台WA2612 AP,客户反馈在WA2612射频卡下绑定两个服务模板,但是现场PC只能搜索到第一个SSID(ChinaNet), WX5004下挂所有AP均无法搜索到第二个SSID(CRI-CIBN)。客户更换终端替换测试,仍然无法搜索到第二个SSID(CRI-CIBN)。
本经验案例中的AC使用的是WX5004无线控制器,AP使用的是WX2612。
1、查看客户WX5004上面配置,发现所有AP均为自动注册。
#
wlan auto-ap enable
#
wlan ap zhidong model WA2612 id 3
serial-id auto
radio 1
service-template 1
service-template 2
radio enable
#
[H3C]dis wlan ap all
Total Number of APs configured : 1
Total Number of configured APs connected : 0
Total Number of auto APs connected : 90
AP Profiles
State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad
C = Config, R = Run, KU = KeyUpdate, KC = KeyCfm
--------------------------------------------------------------------------------
AP Name State Model Serial-ID
--------------------------------------------------------------------------------
zhidong_0033 R/M WA2612 219801A0CJC124000730
zhidong_0034 R/M WA2612 219801A0CJC124000489
zhidong I WA2612 auto
zhidong_0035 R/M WA2612 219801A0CJC124000696
zhidong_0025 R/M WA2612 219801A0CJC124000136
zhidong_0036 R/M WA2612 219801A0CJC124001674
--------------------------------------------------------------------------------
2、通过命令display wlan ap all verbose,同时,在AP隐藏视图下通过命令display ar5drv 1 bss all查看AP射频卡下面只有一个BSS。
AP Profile: zhidong_0036 (auto)
-------------------------------------------------------------------------------
APID : 6
AP System Name : Not Configured
Map Configuration : Not Configured
State : Run
Up Time(hh:mm:ss) : 7 Days, 05:44:56
Model : WA2612
Serial-ID : 219801A0CJC124001674
IP Address : 10.101.4.32
H/W Version : Ver.E
S/W Version : V100R003B03D018
Boot-Rom Version : 1.06
Description : Not Configured
Connection Type : Master
Peer AC MAC Address : -NA-
Priority Level : 4
Echo Interval(s) : 10
Statistics report Interval(s) : 50
Cir(Kbps) : -NA-
Cbs(Bytes) : -NA-
Jumboframe Threshold : Disable
Transmitted control packets : 233679
Received control packets : 233666
Transmitted data packets : 1286209
Received data packets : 131382
Configuration Failure Count : 0
Last Failure Reason :
Last Reboot Reason : Tunnel Initiated
Latest IP Address : -NA-
Tunnel Down Reason : -NA-
Connection Count : 1
-------------------------------------------------------------------------------
AP Mode : Split
AP operation mode : Normal
Portal Service : Disable
Device Detection : Disable
Maximum Number of Radios : 1
Current Number of Radios : 1
Client Keep-alive Interval : Disable
Client Idle Interval(s) : 3600
Broadcast-probe Reply Status : Enable
Radio 1:
Basic BSSID : 5866-baea-6e60
Current BSS Count : 1
Running Clients Count : 0
Wireless Mode : 11gn
Client Dot11n-only : Disabled
Channel Band-width : 20MHz
Secondary Channel Offset : SCN
HT Protection Mode : no protection
Short GI for 20MHz : Supported
Short GI for 40MHz : Supported
Mandatory MCS Set :
Support MCS Set : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15
A-MSDU : Enabled
A-MPDU : Enabled
Configured Channel : auto(6)
Configured Power (dBm) : 24
Interference (%) : -NA-
Channel Load (%) : -NA-
Utilization (%) : -NA-
Co-channel Neighbor Count : -NA-
Channel Health : -NA-
Preamble Type : short
Radio Policy : default_rp
Service Template : 1
SSID : ChinaNet
Port : WLAN-DBSS1:35
Mesh Policy : default_mp_plcy
ANI Support : Enable
11g Protection : Disable
Admin State : UP
Physical State : UP
Operational Rates (Mbps):
1 : mandatory
2 : mandatory
5.5 : mandatory
6 : supported
9 : supported
11 : mandatory
12 : supported
18 : supported
24 : supported
36 : supported
48 : supported
54 : supported
Radar detected Channels : None
Antenna Type : Internal Antenna
Resource Using Ratio (%) : 0
Noise Floor (dBm) : -106
-------------------------------------------------------------------------------
[WA2612-hidecmd]dis ar5 1 bss all
[BssTable Info]:
BasicMacAddr(5866-baea-2e50) BssTblAddr(0x873e7b44) Used(1)/Total(16)
-----------------------------------------------
Bss BssIdx(0) MacAddr(5866-baea-2e50) Status(Run)
[Beacon Info]:
TxBcnCnt(6088830) IsDtim(Y)
BcnHwDescAddr (0xa20071c0) BcnFrmAddr (0x872f1138)
BcnSoftDescAddr(0x803fb4d0) BcnMbufAddr(0x872f0f80)
CabQLastDescAddr(0x00000000)
[Mcast DataFrm Rate]:
auto(11000KBps)
[Security Info]:
N/A
[Default Sib Info]:
TidNum InACQ MinDep Paused ACNum ACInQ BufCnt
0 0 1 0 1 0 0
1 0 1 0 0 0 0
2 0 1 0 0 0 0
3 0 1 0 1 0 0
4 0 1 0 2 0 0
5 0 1 0 2 0 0
6 0 1 0 3 0 0
7 0 1 0 3 0 0
3、经与客户沟通后,发现SSID2:CRI-CIBN是在AP自动注册完成后再在AP射频接口下添加。
4、 该问题最终定位为,AP完成自动注册后,尚未进行AP固化前再在AP射频口下添加服务模板,对于已经完成注册的AP均不生效。所以终端PC无法搜索到第二个SSID(CRI-CIBN)。
1、 在AC用户视图下通过命令reset wlan ap all使AP重新完成注册。
2、 在AC全局视图下通过命令wlan auto-ap persistent all将AP固化后再在射频口下添加服务模板。
3、 建议对AP采用手工注册方式完成配置下发。这样实施的优点是便于后期对于AP管理,方便后期运营维护。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作