S7500E+S3100-8C-EPON-EI(ONU子卡)典型配置
一、 组网需求:
花园镇北某局端机房有一台H3C S7502E作为EPON OLT设备通过无源分光器下接若干H3C S3100-8C-EPON-EI交换机(处于用户侧),现客户要求为花园镇北星星小区5幢3单元住户提供FTTB接入,并实现从局端远程统一管理下行设备,针对此方案提出了如下需求:
1、从S31交换机端口 1~8传输上来的数据,均打上各自端口的VLAN Tag(端口1~4属于VLAN 20供用户上网使用,端口5~8属于VLAN 30供点播使用)。
2、VLAN 20,VLAN 30中,各个端口相互隔离。
3、在S31交换机上开启各端口环路检测功能。
二、 组网图:
三、 配置步骤:
OLT端口配置
[S7502E-Olt2/0/1]dis this
#
interface olt2/0/1 //进入olt端口视图
description Huayuanzhenbei //花园镇北
using onu 1 to 64 //创建onu端口,一个OLT端口下最多能创建64个onu端口
port link-type hybrid //设置olt端口链路类型为Hybrid
undo port hybrid vlan 1 //不允许未规划的默认VLAN通过
port hybrid vlan 20 30 tagged //设置允许通过当前OLT端口的VLAN,并设置发送这些VLAN的报文时携带VLAN Tag
port-isolate enable //开启OLT端口隔离
#
return
ONU远程管理配置
[S7502E-Onu2/0/1:1]dis this
#
interface onu2/0/1:1 //进入onu端口视图
description XingXingXiaoQu 5# 3-Danyuan //星星小区5幢3单元
bind onuid 000f-e274-662c //绑定onu
upstream-sla maximum-bandwidth 1600 //设置上行流量最大带宽,单位为64Kbps,默认上行流量最大带宽为23M
port link-type trunk //设置onu端口链路模式为Trunk
uni 1 vlan-mode tag pvid 20 //设置端口vlan处理模式为tag模式,pvid为20供用户上网使用,该配置下发到S31交换机电口上表现为hybrid端口
uni 2 vlan-mode tag pvid 20
uni 3 vlan-mode tag pvid 20
uni 4 vlan-mode tag pvid 20
uni 5 vlan-mode tag pvid 30 //设置端口vlan处理模式为tag模式,pvid为30供用户点播使用
uni 6 vlan-mode tag pvid 30
uni 7 vlan-mode tag pvid 30
uni 8 vlan-mode tag pvid 30
#
return
S3100-8C-EPON-EI配置
[S3100-8C-EPON-EI]loopback-detection enable //全局开启端口环路检测功能
[S3100-8C-EPON-EI]interface e1/0/1
[S3100-8C-EPON-EI-Ethernet1/0/1]port isolate //开启端口隔离
[S3100-8C-EPON-EI-Ethernet1/0/1]loopback-detection enable //开启端口环路检测功能
[S3100-8C-EPON-EI-Ethernet1/0/1]interface e1/0/2
[S3100-8C-EPON-EI-Ethernet1/0/2]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/2]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/2]interface e1/0/3
[S3100-8C-EPON-EI-Ethernet1/0/3]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/3]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/3]interface e1/0/4
[S3100-8C-EPON-EI-Ethernet1/0/4]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/4]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/4]interface e1/0/5
[S3100-8C-EPON-EI-Ethernet1/0/5]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/5]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/5]interface e1/0/6
[S3100-8C-EPON-EI-Ethernet1/0/6]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/6]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/6]interface e1/0/7
[S3100-8C-EPON-EI-Ethernet1/0/7]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/7]loopback-detection enable
[S3100-8C-EPON-EI-Ethernet1/0/7]interface e1/0/8
[S3100-8C-EPON-EI-Ethernet1/0/8]port isolate
[S3100-8C-EPON-EI-Ethernet1/0/8]loopback-detection enable
四、 配置关键点:
1、确保ONU端口链路模式为Trunk以允许下行所有VLAN通过。
2、默认上行流量最大带宽为23M,单位为64K,需要手动将其设置到较大值。
3、UNI端口功能由S31交换机提供。
4、在S31交换机上开启各个端口的端口隔离及环路检测功能。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作