H3C无线控制器二层注册典型配置举例（V7）

本文档介绍AP与AC间通过二层网络完成注册的配置举例。

本文档适用于使用Comware V7软件版本的无线控制器和接入点产品，不严格与具体硬件版本对应，如果使用过程中与产品实际情况有差异，请参考相关产品手册，或以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置，为了保证配置效果，请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解WLAN接入相关特性。

如图1所示，集中式转发架构下，无线客户端Client、有线客户端Host通过L2 switch和AC相连，L2 switch通过PoE方式给AP供电，AC做为DHCP server为AP、Client和Host分配IP地址。需要实现无线客户端Client通过AP连接到AC上，并能与有线客户端Host互相访问。

1.1  配置思路

·              在AC上开启DHCP server功能，AP、无线客户端Client和有线客户端Host都能通过DHCP server自动获取IP地址。

·              在L2 switch上开启PoE功能，为AP设备供电。

·              在AC上配置无线服务，确保Client可以通过配置的无线服务接入网络，并访问Host。

1.2  配置步骤

1.2.1  配置AC

(1)      配置DHCP server

# 开启DHCP server功能。

system-view

[AC] dhcp enable

# 配置DHCP地址池1为AP分配地址范围为192.168.201.0/24，网关地址为192.168.201.1。

[AC] dhcp server ip-pool 1

[AC-dhcp-pool-1] network 192.168.201.0 mask 255.255.255.0

[AC-dhcp-pool-1] gateway-list 192.168.201.1

[AC-dhcp-pool-1] quit

# 配置DHCP地址池2为Client分配地址范围为192.168.202.0/24，网关地址为192.168.202.1。

[AC] dhcp server ip-pool 2

[AC-dhcp-pool-2] network 192.168.202.0 mask 255.255.255.0 

[AC-dhcp-pool-2] gateway-list 192.168.202.1

[AC-dhcp-pool-2] quit

# 配置DHCP地址池3为Host分配地址范围为192.168.203.0/24，网关地址为192.168.203.1。

[AC] dhcp server ip-pool 3

[AC-dhcp-pool-3] network 192.168.203.0 mask 255.255.255.0

[AC-dhcp-pool-3] gateway-list 192.168.203.1 

[AC-dhcp-pool-3] quit

(2)      配置AC的接口

# 创建VLAN 100及其对应的VLAN接口，并为该接口配置IP地址。AP将获取该IP地址与AC建立CAPWAP隧道。

[AC] vlan 100

[AC-vlan100] quit

[AC] interface vlan-interface 100

[AC-Vlan-interface100] ip address 192.168.201.1 255.255.255.0

[AC-Vlan-interface100] quit

# 创建VLAN 200及其对应的VLAN接口，并为该接口配置IP地址。Client使用该VLAN接入无线网络。

[AC] vlan 200

[AC-vlan200] quit

[AC] interface vlan-interface 200

[AC-Vlan-interface200] ip address 192.168.202.1 24

[AC-Vlan-interface200] quit

# 创建VLAN 300及其对应的VLAN接口，并为该接口配置IP地址。Host使用该VLAN与AC建立连接。

[AC] vlan 300

[AC-vlan300] quit

[AC] interface vlan-interface 300

[AC-Vlan-interface300] ip address 192.168.203.1 24

[AC-Vlan-interface300] quit

# 配置AC和L2 switch相连的接口GigabitEthernet1/0/1为Trunk类型，禁止VLAN 1报文通过，允许VLAN 100、VLAN 200和VLAN 300通过，当前Trunk口的PVID为100。

[AC] interface gigabitethernet 1/0/1

[AC-GigabitEthernet1/0/1] port link-type trunk

[AC-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC-GigabitEthernet1/0/1] port trunk permit vlan 100 200 300

[AC-GigabitEthernet1/0/1] port trunk pvid vlan 100

[AC-GigabitEthernet1/0/1] quit

(3)      配置无线服务

# 创建无线服务模板1，并进入无线服务模板视图。

[AC] wlan service-template 1

# 配置SSID为service。

[AC-wlan-st-1] ssid service

# 使能服务模板。

[AC-wlan-st-1] service-template enable

[AC-wlan-st-1] quit

(4)      配置AP

# 创建手工AP，名称为officeap，型号名称为WA4320i-ACN。

[AC] wlan ap officeap model WA4320i-ACN

# 设置AP的序列号为210235A1Q2C159000018。

[AC-wlan-ap-officeap] serial-id 210235A1Q2C159000018

# 进入AP的Radio 1视图，将无线服务模板1绑定到Radio 1上，并指定客户端上线的VLAN为VLAN 200。

[AC-wlan-ap-officeap] radio 1

[AC-wlan-ap-officeap-radio-1] service-template 1 vlan 200

# 开启Radio 1的射频功能。

[AC-wlan-ap-officeap-radio-1] radio enable

[AC-wlan-ap-officeap-radio-1] return

1.2.2  配置L2 switch

# 创建VLAN 100、VLAN 200和VLAN 300，其中VLAN 100用于转发AC和AP间CAPWAP隧道内的流量，VLAN 200为无线客户端接入的VLAN，VLAN 300为Host接入的VLAN。

system-view

[L2 switch] vlan 100

[L2 switch-vlan100] quit

[L2 switch] vlan 200

[L2 switch-vlan200] quit

[L2 switch] vlan 300

[L2 switch-vlan300] quit

# 配置L2 switch和AC相连的接口GigabitEthernet1/0/1为Trunk类型，允许VLAN 100、VLAN 200和VLAN 300通过，当前Trunk口的PVID为100。

[L2 switch] interface gigabitEthernet 1/0/1

[L2 switch-GigabitEthernet1/0/1] port link-type trunk

[L2 switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200 300

[L2 switch-GigabitEthernet1/0/1] port trunk pvid vlan 100

[L2 switch-GigabitEthernet1/0/1] quit

# 配置L2 switch和AP相连的接口GigabitEthernet1/0/2为Trunk类型，禁止VLAN 1报文通过，允许VLAN 100和VLAN 200通过，当前Trunk口的PVID为100，并开启PoE远程供电功能。

[L2 switch] interfac gigabitEthernet 1/0/2

[L2 switch-GigabitEthernet1/0/2] port link-type trunk 

[L2 switch-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[L2 switch-GigabitEthernet1/0/2] port trunk permit vlan 100 200

[L2 switch-GigabitEthernet1/0/2] port trunk pvid vlan 100

[L2 switch-GigabitEthernet1/0/2] poe enable

[L2 switch-GigabitEthernet1/0/2] quit

# 配置L2 switch和Host相连的接口GigabitEthernet1/0/3为Access类型，允许VLAN 300通过。

[L2 switch] interfac gigabitEthernet 1/0/3

[L2 switch-GigabitEthernet1/0/3] port access vlan 300

[L2 switch-GigabitEthernet1/0/3] quit

1.3  验证配置

(1)      在AC上查看AP注册信息

# 在AC上使用命令display wlan ap all查看AP，可以看到AP的状态是R/M，表明AP已经成功注册到AC。

display wlan ap all                             

Total number of APs: 1                                                         

Total number of connected APs: 1                                               

Total number of connected manual APs: 1                                        

Total number of connected auto APs: 0                                          

Total number of connected anchor APs: 0                                        

Maximum supported APs: 3072                                                    

Remaining APs: 3071                                                             

Fit APs activated by license: 512                                              

Remaining fit APs: 511                                                         

WTUs activated by license: 2500                                                

Remaining WTUs: 2500                                                           

                                                                               

                                 AP information                                

 State : I = Idle,      J  = Join,       JA = JoinAck,    IL = ImageLoad       

         C = Config,    DC = DataCheck,  R  = Run,   M = Master,  B = Backup   

                                                                                

AP name                AP ID   State   Model             Serial ID             

--------------------------------------------------------------------------------

officeap               1       R/M     WA4320i-ACN       210235A1Q2C159000018 

(2)      在AC上查看Client信息

# 在AC上使用命令display wlan client查看在线Client，可以看到Client已经连接到AP的radio1。

display wlan client                                                       

Total number of clients: 1                                                      

                                                                               

MAC address    Username             APID/RID  IP address                 VLAN ID

109a-dd9d-fc68 N/A                     1/1    192.168.202.4              200   

(3)      Host与Client可以相互ping通

# Client 通过DHCP server获取到IP地址192.168.202.4，在Host上ping Client的IP地址可以ping通。同理，在Client上ping Host的IP地址也能ping通，不再赘述。

C:\Users\system32>ping 192.168.202.4 -t

 

Pinging 192.168.202.4 with 32 bytes of data:

Reply from 192.168.202.4: bytes=32 time=8ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

Reply from 192.168.202.4: bytes=32 time<1ms TTL=255

 

Ping statistics for 192.168.202.4:

    Packets: Sent = 11, Received = 11, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 0ms, Maximum = 8ms, Average = 0ms

Control-C

^C

C:\Users\system32>

1.4  配置文件

·              AC

#                                                                              

 dhcp enable                                                                   

#                                                                              

vlan 1                                                                         

#                                                                              

vlan 100                                                                 

#                                                                              

vlan 200                                                                

#      

vlan 300                                                                 

#      

dhcp server ip-pool 1                                                          

 gateway-list 192.168.201.1                                                    

 network 192.168.201.0 mask 255.255.255.0                                      

#                                                                              

dhcp server ip-pool 2                                                          

 gateway-list 192.168.202.1                                                    

 network 192.168.202.0 mask 255.255.255.0                                      

#                                                                              

dhcp server ip-pool 3                                                           

 gateway-list 192.168.203.1                                                    

 network 192.168.203.0 mask 255.255.255.0                                      

#                                                                               

wlan service-template 1                                                        

 ssid service                                                                 

 service-template enable                                                        

#                                                                              

interface Vlan-interface1                                                      

#                                                                               

interface Vlan-interface100                                                    

 ip address 192.168.201.1 255.255.255.0                                        

#                                                                              

interface Vlan-interface200                                                    

 ip address 192.168.202.1 255.255.255.0                                        

#                                                                              

interface Vlan-interface300                                                    

 ip address 192.168.203.1 255.255.255.0                                        

#                                                                              

interface GigabitEthernet1/0/1                                                  

 port link-type trunk                                                          

 undo port trunk permit vlan 1

port trunk permit vlan 100 200 300

port trunk pvid vlan 100                                           

#                                                                              

wlan ap officeap model WA4320i-ACN                                           

 serial-id 210235A1Q2C159000018                                                 

vlan 1

 radio 1                                                                       

  radio enable                                                                 

  service-template 1 vlan 200                                                  

 radio 2  

#                                                                              

·              L2 switch

#                                                                              

vlan 100                                                                        

#                                                                              

vlan 200                                                                       

#                                                                               

vlan 300                                                                       

#                                                                              

interface GigabitEthernet1/0/1                                                  

 port link-type trunk                                                          

 undo port trunk permit vlan 1 100 200 300                                     

port trunk pvid vlan 100

#                                                                               

interface GigabitEthernet1/0/2                                                 

 port link-type trunk                                                          

 undo port trunk permit vlan 1                                                 

 port trunk permit vlan 100 200                                               

 port trunk pvid vlan 100                                                      

 poe enable

#                                                                               

interface GigabitEthernet1/0/3                                                 

 port access vlan 300                                                          

#                                                                               

·              配置AP的序列号时请确保该序列号与AP唯一对应，AP的序列号可以通过AP设备背面的标签获取。

·              配置L2 switch和AP相连的接口禁止VLAN 1报文通过，以防止VLAN 1内报文过多。