问

F5000光电转换

2022-07-06提问

0关注
1收藏，1415浏览

proposal

proposal 五段

粉丝：1人关注：1人

问题描述：

F5000设备是否支持光电转换,直接接光电转换模块起不来.

组网及组网描述：

最佳答案

已采纳

叫我靓仔

叫我靓仔九段

粉丝：160人关注：1人

光转电视独立于设备的，纯硬件，起不来进系统检查是否识别

回复proposal:

你再确认下你手头这个光电模块是好的，也可以多找几个试试

叫我靓仔发表时间：2022-07-06 更多>>

怎么查看有没有识别到?,光模块可以看到收发光,光电转换看什么

proposal 发表时间：2022-07-06

回复proposal:

dis interface x 看下media type里有没有内容，另外可以保持console插着的状态，插拔看日志

叫我靓仔发表时间：2022-07-06

识别到了的

proposal 发表时间：2022-07-06

回复叫我靓仔:

%Jul 6 15:39:28:315 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_IN: Ten-GigabitEthernet1/1/3: The transceiver is 1000_BASE_T_AN_SFP. %Jul 6 15:39:28:315 2022 ECL-10F-X04-F5000 OPTMOD/5/TX_ALM_OFF: Ten-GigabitEthernet1/1/3: Tx fault removed. %Jul 6 15:39:28:898 2022 ECL-10F-X04-F5000 OPTMOD/5/RX_ALM_OFF: Ten-GigabitEthernet1/1/3: Rx los removed. %Jul 6 15:41:52:841 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_OUT: Ten-GigabitEthernet1/1/3: Transceiver absent. %Jul 6 15:43:49:660 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_OUT: Ten-GigabitEthernet1/1/0: Transceiver absent. %Jul 6 15:43:59:542 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_IN: Ten-GigabitEthernet1/1/0: The transceiver is 1000_BASE_T_AN_SFP. %Jul 6 15:46:18:234 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_OUT: Ten-GigabitEthernet1/1/0: Transceiver absent. %Jul 6 15:46:22:280 2022 ECL-10F-X04-F5000 OPTMOD/4/MODULE_IN: Ten-GigabitEthernet1/1/0: The transceiver is 1000_BASE_T_AN_SFP. Ten-GigabitEthernet1/1/0 Current state: DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: 4ce9-e4ae-2810 Description: to-huawei-wangguan Loopback is not set Media type is optical fiber, loopback not set, promiscuous mode set Speed Negotiation, Duplex Negotiation, link type is force link Output flow-control is disabled, input flow-control is disabled 1000Mbps-speed mode, full-duplex mode Link speed type is force link, link duplex type is force link Flow-control is not enabled Maximum frame length: 9216 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 850 MDI type: Automdix Port link-type: Access Tagged VLANs: None Untagged VLANs: 850 Last link flapping: Never Last clearing of counters: Never Peak input rate: 0 bytes/sec, at 00-00-00 00:00:00 Peak output rate: 0 bytes/sec, at 00-00-00 00:00:00 Last 300 second input: 0 packets/sec 0 bytes/sec 0% Last 300 second output: 0 packets/sec 0 bytes/sec 0% Input (total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input (normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, - throttles 0 CRC, 0 frame, 0 overruns, 0 aborts 0 ignored, - parity errors Output (total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Output (normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses Output: 0 output errors, 0 underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, 0 no carrier interface Ten-GigabitEthernet1/1/0 port link-mode bridge description to-huawei-wangguan port access vlan 850 speed 1000 duplex full

proposal 发表时间：2022-07-06

回复proposal:

你接PC看看有没有反应

叫我靓仔发表时间：2022-07-06

回复叫我靓仔:

一样不行,你试过F5000使用光电转换模块吗?我看到有的设备是不支持的

proposal 发表时间：2022-07-06

回复proposal:

那就是不支持了

叫我靓仔发表时间：2022-07-06

回复proposal:

你再确认下你手头这个光电模块是好的，也可以多找几个试试