您好，参考

H3C无线控制器云集群典型配置举例

1  注意事项

如果是通过其它组网方式升级过来，建议先清空配置重启，搭建集群组网，再配置其它业务。

2  配置举例

2.1  组网需求

如图1所示，AC 1与AC 2通过直连链路建立云集群，同时AC1作为初始主，云集群与交换机Core之间建立动态聚合链路，用于LACP MAD检测和业务报文转发。

图1 双机直连组网图

2.2  配置步骤

2.2.1  配置Switch

# 配置前提：Core完成堆叠建立

# 创建二层聚合接口1，并配置该聚合接口对应的聚合组工作在动态聚合模式下。

<Switch> system-view

[Switch] interface bridge-aggregation 1

Switch-Bridge-Aggregation1] link-aggregation mode dynamic

[Switch-Bridge-Aggregation1] quit

# 将端口Ten-GigabitEthernet1/0/2加入到聚合组1中。

[Switch] interface ten-gigabitethernet 1/0/2

[Switch-Ten-GigabitEthernet1/0/1] port link-aggregation group 1

[Switch-Ten-GigabitEthernet1/0/1] quit

# 将端口Ten-GigabitEthernet2/0/2加入到聚合组1中。

[Switch] interface ten-gigabitethernet 2/0/2

[Switch-Ten-GigabitEthernet1/0/2] port link-aggregation group 1

[Switch-Ten-GigabitEthernet1/0/2] quit

2.2.2  配置AC 1

(1)       配置云集群member成员

#设备出厂默认member id 为1，如果还想作为member id 1使用，不需要配置

<AC1> system-view

[AC1] cloud-cluster member 1

[AC1-ccluster-member-1]

(2)       配置成员ip

#云集群自身要单独占用一个IP网段，需要提前规划好（本文以192.168.10.x/24举例）

#成员IP地址（不是接口IP）AC1与AC2同网段

[AC1-ccluster-member-1]member-ip 192.168.10.10 24

(3)       指定主设备（初始主）的ip地址（本例是AC1的member ip）

[AC1-ccluster-member-1]join-cluster ip 192.168.10.10

(4)       绑定云集群端口

#云集群需要配置控制通道和数据通道的物理接口

#每个通道两个物理口是为了冗余备份

#数据通道走私有协议，会增加额外的数据头，对带宽有要求，推荐使用XGE口，如果使用GE口，至少要2个。

 [AC1-ccluster-member-1]cluster-link control bind interface GigabitEthernet 1/0/2

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC1-ccluster-member-1]cluster-link control bind interface GigabitEthernet 1/0/3

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC1-ccluster-member-1]cluster-link data bind interface Ten-GigabitEthernet 1/3/8

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC1-ccluster-member-1]cluster-link data bind interface Ten-GigabitEthernet 1/3/9

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

(5)       激活云集群配置

[AC1-ccluster-member-1]quit

[AC1]cloud-cluster configuration active

New cluster configuration:

  cloud-cluster service-cluster domain 0

  cloud-cluster hello cloud-timeout 3 service-timeout 5

  cloud-cluster member 1

    member-ip 192.168.10.10/24

    join-cluster ip 192.168.10.10

    role manager-worker

cluster-link control bind interface GigabitEthernet1/0/2

cluster-link data bind interface Ten-GigabitEthernet 1/3/9

The system will activate and save the configuration, and it might do a restart. Continue? [Y/N]:y

The current configuration will be written to the device. Are you sure? [Y/N]:y

Please input the file name(*.cfg)[flash:/startup.cfg]

(To leave the existing filename unchanged, press the enter key):test.cfg

#设备重启，配置生效

2.2.3  配置AC 2

(1)       配置云集群member成员

#设备出厂默认member id 为1，如果要修改成员编号，需要手动配置一次

<AC2> system-view

[AC2]cloud-cluster member 1 renumber 2

This command will take effect after the cloud cluster configuration is activated. The command might result in configuration change or loss when it takes effect. Continue? [Y/N]: y

[AC2]cloud-cluster member 1

[AC2-ccluster-member-1]

(2)       配置成员ip

#成员IP地址（非接口IP）AC1与AC2同网段

[AC2-ccluster-member-1]member-ip 192.168.10.11 24

(3)       指定主设备（初始主）的ip地址（本例是AC1的member ip）

[AC2-ccluster-member-1]join-cluster ip 192.168.10.10

(4)       绑定云集群端口

#云集群需要配置控制通道和数据通道的物理接口

#每个通道两个物理口是为了冗余备份

#数据通道走私有协议，会增加额外的数据头，对带宽有要求，推荐使用XGE口，如果使用GE口，至少要2个。

[AC2-ccluster-member-1]cluster-link control bind interface GigabitEthernet 1/0/2

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC2-ccluster-member-1]cluster-link control bind interface GigabitEthernet 1/0/3

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC2-ccluster-member-1]cluster-link data bind interface Ten-GigabitEthernet 1/3/8

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

[AC2-ccluster-member-1]cluster-link data bind interface Ten-GigabitEthernet 1/3/9

The system will shut down and then bring up the interface after activation the cloud cluster configuration. Continue? [Y/N]: y

(5)       激活云集群配置

[AC2-ccluster-member-1]quit

[AC2]cloud-cluster configuration active

New cluster configuration:

  cloud-cluster service-cluster domain 0

  cloud-cluster hello cloud-timeout 3 service-timeout 5

  cloud-cluster member 2

    member-ip 192.168.10.11/24

    join-cluster ip 192.168.10.10

    role manager-worker

cluster-link control bind interface GigabitEthernet2/0/2

cluster-link data bind interface Ten-GigabitEthernet 2/3/9

The system will activate and save the configuration, and it might do a restart. Continue? [Y/N]:y

The current configuration will be written to the device. Are you sure? [Y/N]:y

Please input the file name(*.cfg)[flash:/startup.cfg]

(To leave the existing filename unchanged, press the enter key):test.cfg

#设备重启，配置生效

2.2.4  云集群建立后配置

(1)       云集群建立完成

#重启完成后显示集群状态

<H3C>display cloud-cluster service-cluster container  //查看主备请使用这个命令行

Container ID     Slot ID       Member ID      Role        Status

1                1             1              Master      Online  

2                2             2              Standby     Online

<H3C>display cloud-cluster  //Role的角色可能与本样例不一致，内层主备，可以不关注

Manager list:

Member ID    Role        Member IP           State       Heartbeat(ms)

1            Follower    192.168.10.10       online      100

2            Leader      192.168.10.11       online      0

Worker list:

Member ID    State       Heartbeat(ms)       Joined at

1            online      100                 2023-02-12 06:13:28

2            online      200                 2023-02-12 06:13:28

(2)       配置动态聚合组

<H3C> system-view

#创建二层聚合接口1，并配置该聚合接口对应的聚合组工作在动态聚合模式下。

<H3C> system-view

[H3C] interface bridge-aggregation 1

[H3C-Bridge-Aggregation1] link-aggregation mode dynamic

# 开启LACP MAD检测功能。#要求交换机为我司的交换机

[H3C-Bridge-Aggregation1] mad enable

[H3C-Bridge-Aggregation1] quit

# 将端口Ten-GigabitEthernet1/3/10加入到聚合组1中。

[H3C] interface ten-gigabitethernet 1/3/10

[H3C-Ten-GigabitEthernet1/3/10] port link-aggregation group 1

[H3C-Ten-GigabitEthernet1/3/10] quit

# 将端口Ten-GigabitEthernet2/3/10加入到聚合组1中。

[H3C] interface ten-gigabitethernet 2/3/10

[H3C-Ten-GigabitEthernet2/3/10] port link-aggregation group 1

[H3C-Ten-GigabitEthernet2/3/10 ]quit