防火墙ipsec
- 0关注
- 0收藏，308浏览
最佳答案
V7防火墙ipsec野蛮模式web配置（一对多模式）
组网及说明
总部公网地址172.16.0.1，分支无论地址是否固定。两边私网地址用loopback地址替代。
配置步骤
地址、安全域及安全策略需自行配置放通
一、总部配置
新建ike提议
网络》VPN》ipsec》IKE提议》新建，选择相应的认证加密等参数
认证加密等参数相同的ike提议建议只配置一个，因为参数相同设备只会去匹配优先级最高的那个ike提议，优先级数值越小越优先。
新建ipsec策略
网络》VPN》ipsec》策略》新建，新建相应的ipsec策略等参数
配置ipsec策略的名称，选择接口及地址，总部设备角色选择中心节点。选择中心节点设备会下发模板方式的配置。模板方式的总部不需要配置acl，由分支配置acl来跟总部协商自动出保护的数据流。
IKE策略选择野蛮模式，IKE提议选择之前配置的ike，本端ID选择ipv4地址。
注意：本端ID一定要选择ipv4地址
Ipsec参数选择esp认证加密算法，其他保持默认。
二、分支配置
配置ike提议
网络》VPN》ipsec》IKE提议》新建，选择相应的认证加密等参数，同总部配置
配置ipsec策略和ike策略
网络》VPN》ipsec》策略》新建，新建相应的ipsec策略等参数
注意：本端ID留空，对端ID选择ipv4地址
配置ipsec保护的数据流及ipsec参数
配置关键点
总部采用模板方式无法指定分支的FQDN，总部默认下发配置
ike profile zongbu_IPv4_1
keychain zongbu_IPv4_1
exchange-mode aggressive
local-identity address 172.16.0.1
match remote identity address 0.0.0.0 0.0.0.0
match local address GigabitEthernet1/0/0
proposal 10
指定对端地址为全0，所以分支只能配置身份识别local-identity为地址，又因为大部分采用野蛮模式的分支地址是不固定的，所以分支这里本端ID只能留空，默认local-identity为地址。否则两端因为身份识别方式不一致导致协商不起来。
分支IKE策略--对端ID必须配置ipv4地址，因为分支要主动发起必须知道总部地址，另外如果分支对端ID配置成FQDN的话，下发配置如下。
ike profile fenzhi_IPv4_1
keychain fenzhi_IPv4_1
exchange-mode aggressive
local-identity fqdn fenzhi
match remote identity fqdn zongbu
match local address GigabitEthernet1/0/0
proposal 10
#
ike proposal 10
encryption-algorithm 3des-cbc
dh group2
#
ike keychain fenzhi_IPv4_1
match local address GigabitEthernet1/0/0
pre-shared-key hostname zongbu key cipher $c$3$U4JtiyOgrXVs/aYytzz3IeVQFWDORDQ7
秘钥会指定为hostname，会报找不到对应的密钥从而ike都无法建立。
命令行配置如下：
总部配置
<zongbu>dis cu
#
version 7.1.064, Alpha 7164
#
sysname zongbu
#
context Admin id 1
#
telnet server enable
#
irf mac-address persistent timer
irf auto-update enable
undo irf link-delay
irf member 1 priority 1
#
ospf 1
area 0.0.0.0
network 172.16.0.0 0.0.0.255
#
xbar load-single
password-recovery enable
lpu-type f-series
#
vlan 1
#
interface NULL0
#
interface LoopBack0
ip address 1.1.1.1 255.255.255.255
#
interface GigabitEthernet1/0/0
port link-mode route
combo enable copper
ip address 172.16.0.1 255.255.255.0
ipsec apply policy zongbu
#
interface GigabitEthernet1/0/1
port link-mode route
combo enable copper
ip address 172.16.2.1 255.255.255.0
#
interface GigabitEthernet1/0/2
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/3
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/4
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/5
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/6
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/7
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/8
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/9
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/10
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/11
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/12
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/13
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/14
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/15
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/16
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/17
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/18
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/19
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/20
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/21
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/22
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/23
port link-mode route
combo enable copper
#
security-zone name Local
#
security-zone name Trust
import interface LoopBack0
#
security-zone name DMZ
#
security-zone name Untrust
import interface GigabitEthernet1/0/0
import interface GigabitEthernet1/0/1
#
security-zone name Management
#
scheduler logfile size 16
#
line class aux
user-role network-operator
#
line class console
user-role network-admin
#
line class tty
user-role network-operator
#
line class vty
user-role network-operator
#
line aux 0
user-role network-admin
#
line con 0
authentication-mode scheme
user-role network-admin
#
line vty 0 4
authentication-mode scheme
user-role network-admin
#
line vty 5 63
user-role network-operator
#
ip route-static 0.0.0.0 0 172.16.0.2
#
domain system
#
aaa session-limit ftp 16
aaa session-limit telnet 16
aaa session-limit ssh 16
domain default enable system
#
role name level-0
description Predefined level-0 role
#
role name level-1
description Predefined level-1 role
#
role name level-2
description Predefined level-2 role
#
role name level-3
description Predefined level-3 role
#
role name level-4
description Predefined level-4 role
#
role name level-5
description Predefined level-5 role
#
role name level-6
description Predefined level-6 role
#
role name level-7
description Predefined level-7 role
#
role name level-8
description Predefined level-8 role
#
role name level-9
description Predefined level-9 role
#
role name level-10
description Predefined level-10 role
#
role name level-11
description Predefined level-11 role
#
role name level-12
description Predefined level-12 role
#
role name level-13
description Predefined level-13 role
#
role name level-14
description Predefined level-14 role
#
user-group system
#
local-user admin class manage
password hash $h$6$UbIhNnPevyKUwfpm$LqR3+yg1IjNct39MkOR0H0iQXLkYB3jMqM4vbAeoXOhbabIIFnjJPEGR00YiYA1Sz4LiY3FmEdru2fOLMb1shQ==
service-type telnet terminal http
authorization-attribute user-role level-3
authorization-attribute user-role network-admin
authorization-attribute user-role network-operator
#
ipsec transform-set zongbu_IPv4_1
esp encryption-algorithm 3des-cbc
esp authentication-algorithm sha1
#
ipsec policy-template zongbu 1
transform-set zongbu_IPv4_1
local-address 172.16.0.1
ike-profile zongbu_IPv4_1
#
ipsec policy zongbu 1 isakmp template zongbu
#
ike profile zongbu_IPv4_1
keychain zongbu_IPv4_1
exchange-mode aggressive
local-identity address 172.16.0.1
match remote identity address 0.0.0.0 0.0.0.0
match local address GigabitEthernet1/0/0
proposal 10
#
ike proposal 10
encryption-algorithm 3des-cbc
dh group2
#
ike keychain zongbu_IPv4_1
match local address GigabitEthernet1/0/0
pre-shared-key address 0.0.0.0 0.0.0.0 key cipher $c$3$nw8o7yIcjPSdFyAURIYIKXSd/sFIJgEN
#
ip http enable
ip https enable
#
security-policy ip
rule 1 name test
action pass
#
return
<zongbu>
<zongbu>dis ike sa
Connection-ID Remote Flag DOI
------------------------------------------------------------------
9 172.16.1.1 RD IPsec
Flags:
RD--READY RL--REPLACED FD-FADING RK-REKEY
<zongbu>dis ipse
<zongbu>dis ipsec sa
<zongbu>dis ipsec sa
-------------------------------
Interface: GigabitEthernet1/0/0
-------------------------------
-----------------------------
IPsec policy: zongbu
Sequence number: 1
Mode: Template
-----------------------------
Tunnel id: 0
Encapsulation mode: tunnel
Perfect Forward Secrecy:
Inside VPN:
Extended Sequence Numbers enable: N
Traffic Flow Confidentiality enable: N
Path MTU: 1444
Tunnel:
local address: 172.16.0.1
remote address: 172.16.1.1
Flow:
sour addr: 1.1.1.1/255.255.255.255 port: 0 protocol: ip
dest addr: 2.2.2.2/255.255.255.255 port: 0 protocol: ip
[Inbound ESP SAs]
SPI: 1511053843 (0x5a10da13)
Connection ID: 12884901891
Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1
SA duration (kilobytes/sec): 1843200/3600
SA remaining duration (kilobytes/sec): 1843199/2576
Max received sequence-number: 5
Anti-replay check enable: Y
Anti-replay window size: 64
UDP encapsulation used for NAT traversal: N
Status: Active
[Outbound ESP SAs]
SPI: 3440085931 (0xcd0b8bab)
Connection ID: 12884901890
Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1
SA duration (kilobytes/sec): 1843200/3600
SA remaining duration (kilobytes/sec): 1843199/2576
Max sent sequence-number: 5
UDP encapsulation used for NAT traversal: N
Status: Active
<zongbu>
分支配置
<fenzhi>dis cu
#
version 7.1.064, Alpha 7164
#
sysname fenzhi
#
context Admin id 1
#
telnet server enable
#
irf mac-address persistent timer
irf auto-update enable
undo irf link-delay
irf member 1 priority 1
#
ospf 1
area 0.0.0.0
network 172.16.1.0 0.0.0.255
#
xbar load-single
password-recovery enable
lpu-type f-series
#
vlan 1
#
interface NULL0
#
interface LoopBack0
ip address 2.2.2.2 255.255.255.255
#
interface GigabitEthernet1/0/0
port link-mode route
combo enable copper
ip address 172.16.1.1 255.255.255.0
ipsec apply policy fenzhi
#
interface GigabitEthernet1/0/1
port link-mode route
combo enable copper
ip address 172.16.2.2 255.255.255.0
#
interface GigabitEthernet1/0/2
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/3
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/4
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/5
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/6
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/7
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/8
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/9
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/10
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/11
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/12
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/13
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/14
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/15
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/16
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/17
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/18
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/19
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/20
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/21
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/22
port link-mode route
combo enable copper
#
interface GigabitEthernet1/0/23
port link-mode route
combo enable copper
#
security-zone name Local
#
security-zone name Trust
import interface LoopBack0
#
security-zone name DMZ
#
security-zone name Untrust
import interface GigabitEthernet1/0/0
import interface GigabitEthernet1/0/1
#
security-zone name Management
#
scheduler logfile size 16
#
line class aux
user-role network-operator
#
line class console
user-role network-admin
#
line class tty
user-role network-operator
#
line class vty
user-role network-operator
#
line aux 0
user-role network-admin
#
line con 0
authentication-mode scheme
user-role network-admin
#
line vty 0 4
authentication-mode none
user-role network-admin
#
line vty 5 63
authentication-mode none
user-role network-operator
#
ip route-static 0.0.0.0 0 172.16.1.2
#
acl advanced name IPsec_fenzhi_IPv4_1
rule 1 permit ip source 2.2.2.2 0 destination 1.1.1.1 0
#
domain system
#
aaa session-limit ftp 16
aaa session-limit telnet 16
aaa session-limit ssh 16
domain default enable system
#
role name level-0
description Predefined level-0 role
#
role name level-1
description Predefined level-1 role
#
role name level-2
description Predefined level-2 role
#
role name level-3
description Predefined level-3 role
#
role name level-4
description Predefined level-4 role
#
role name level-5
description Predefined level-5 role
#
role name level-6
description Predefined level-6 role
#
role name level-7
description Predefined level-7 role
#
role name level-8
description Predefined level-8 role
#
role name level-9
description Predefined level-9 role
#
role name level-10
description Predefined level-10 role
#
role name level-11
description Predefined level-11 role
#
role name level-12
description Predefined level-12 role
#
role name level-13
description Predefined level-13 role
#
role name level-14
description Predefined level-14 role
#
user-group system
#
local-user admin class manage
password hash $h$6$UbIhNnPevyKUwfpm$LqR3+yg1IjNct39MkOR0H0iQXLkYB3jMqM4vbAeoXOhbabIIFnjJPEGR00YiYA1Sz4LiY3FmEdru2fOLMb1shQ==
service-type telnet terminal http
authorization-attribute user-role level-3
authorization-attribute user-role network-admin
authorization-attribute user-role network-operator
#
ipsec transform-set fenzhi_IPv4_1
esp encryption-algorithm 3des-cbc
esp authentication-algorithm sha1
#
ipsec policy fenzhi 1 isakmp
transform-set fenzhi_IPv4_1
security acl name IPsec_fenzhi_IPv4_1
remote-address 172.16.0.1
ike-profile fenzhi_IPv4_1
#
ike profile fenzhi_IPv4_1
keychain fenzhi_IPv4_1
exchange-mode aggressive
match remote identity address 172.16.0.1 255.255.255.255
match local address GigabitEthernet1/0/0
proposal 10
#
ike proposal 10
encryption-algorithm 3des-cbc
dh group2
#
ike keychain fenzhi_IPv4_1
match local address GigabitEthernet1/0/0
pre-shared-key address 172.16.0.1 255.255.255.255 key cipher $c$3$0D8k6aHsDClx2d/siPNHdmCMjeDjWHJR
#
ip http enable
ip https enable
#
security-policy ip
rule 1 name test
action pass
#
return
<fenzhi>
<fenzhi>dis ike sa
Connection-ID Remote Flag DOI
------------------------------------------------------------------
37 172.16.0.1 RD IPsec
Flags:
RD--READY RL--REPLACED FD-FADING RK-REKEY
<fenzhi>dis ipse
<fenzhi>dis ipsec sa
<fenzhi>dis ipsec sa
-------------------------------
Interface: GigabitEthernet1/0/0
-------------------------------
-----------------------------
IPsec policy: fenzhi
Sequence number: 1
Mode: ISAKMP
-----------------------------
Tunnel id: 0
Encapsulation mode: tunnel
Perfect Forward Secrecy:
Inside VPN:
Extended Sequence Numbers enable: N
Traffic Flow Confidentiality enable: N
Path MTU: 1444
Tunnel:
local address: 172.16.1.1
remote address: 172.16.0.1
Flow:
sour addr: 2.2.2.2/255.255.255.255 port: 0 protocol: ip
dest addr: 1.1.1.1/255.255.255.255 port: 0 protocol: ip
[Inbound ESP SAs]
SPI: 3440085931 (0xcd0b8bab)
Connection ID: 12884901891
Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1
SA duration (kilobytes/sec): 1843200/3600
SA remaining duration (kilobytes/sec): 1843199/2400
Max received sequence-number: 5
Anti-replay check enable: Y
Anti-replay window size: 64
UDP encapsulation used for NAT traversal: N
Status: Active
[Outbound ESP SAs]
SPI: 1511053843 (0x5a10da13)
Connection ID: 12884901890
Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1
SA duration (kilobytes/sec): 1843200/3600
SA remaining duration (kilobytes/sec): 1843199/2400
Max sent sequence-number: 5
UDP encapsulation used for NAT traversal: N
Status: Active
- 2024-07-05回答
- 评论(0)
- 举报
-
(0)
什么型号的设备
- 2024-07-05回答
- 评论(2)
- 举报
-
(0)
https://zhiliao.h3c.com/Theme/details/144557
F1000-AK
https://zhiliao.h3c.com/Theme/details/144557
编辑答案
亲~登录后才可以操作哦!
确定你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
- 1. 您举报的内容是什么？（请在邮件中列出您举报的内容和链接地址）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
- 3. 是哪家企业？（营业执照，单位登记证明等证件）
- 4. 您与该企业的关系是？（您是企业法人或被授权人，需提供企业委托授权书）
抄袭了我的内容
×
原文链接或出处
诽谤我
×
- 1. 您举报的内容以及侵犯了您什么权益？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
对根叔社区有害的内容
×
不规范转载
×
举报说明