wa5320i-LI无线ap如何切换成胖模式，需要详细一点

参考

https://www.h3c.com/cn/Service/Document_Software/Document_Center/Home/Wlan/00-Public/Quick_Starts/Quick_Maintenance/H3C_WiFi6_GZMS/?CHID=558937

 通过AP BootWare菜单切换

1. 切换前准备

本文以Cloud切换FIT模式举例，在进行工作模式切换之前，请将PC的Console线缆连接到AP的Console口。

图2-7 通过AP命令行切换工作模式组网图

2. 切换步骤

# 执行reboot命令重启AP，在AP重新启动和上电的过程中，在配置终端的屏幕上将显示：

<AP>reboot

Start to check configuration with next startup configuration file, please wait..

.......DONE!

This command will reboot the device. Continue? [Y/N]:y

Now rebooting, please wait...

%Apr 11 23:36:57:760 2021 H3C DEV/5/SYSTEM_REBOOT: System is rebooting now.

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU...

Booting Normal Extended BootWare

The Extended BootWare is self-decompressing..................Done.

***********************************************************************

*                                                                     *

*                   H3C WA6636 BootWare, Version 7.12                 *

*                                                                     *

***********************************************************************

Copyright (c) 2004-2021 New H3C Technologies Co., Ltd.

Compiled Date       : Jan 28 2021

CPU L1 Cache        : 32KB

CPU L2 Cache        : 256KB

CPU Clock Speed     : 2200MHz

Memory Type         : DDR3 SDRAM

Memory Size         : 1024MB

Memory Speed        : 933MHz

Flash Size          : 256MB

PCB Version         : Ver.A

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

# 当出现“Press Ctrl+B to access EXTENDED-BOOTWARE MENU...”时，键入<Ctrl+B>，系统进入BootWare主菜单：

Password recovery capability is enabled.

Note: The current operating device is flash

Enter < Storage Device Operation > to select device.

==========================<EXTENDED-BOOTWARE MENU>======================

|<1> Boot System                                                        |

|<2> Enter Serial SubMenu                                               |

|<3> Enter Ethernet SubMenu                                             |

|<4> File Control                                                       |

|<5> Restore to Factory Default Configuration                           |

|<6> Skip Current System Configuration                                  |

|<7> BootWare Operation Menu                                            |

|<8> Skip Authentication for Console Login                              |

|<9> Storage Device Operation                                           |

|<0> Reboot                                                             |

=======================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Enter your choice(0-9):

# 在BootWare主菜单下键入<Ctrl+Y>，可以进入AP工作模式切换菜单，系统显示如下：

Please select the new mode

Current mode is Cloud Mode

=======================================================================

|NO.  Mode                                                             |

|1    Fit Mode                                                         |

|2    Anchor-AC   (Virtual AC Mode)                                    |

|3    Cloud Mode                                                       |

|0    Exit                                                             |

=======================================================================

# 在AP工作模式切换菜单下键入相对应的数字，即可切换到对应的工作模式，当出现如下提示信息时，工作模式切换成功。

Enter your choice(0-3):1

Changed to fit mode successfully!

2.5  通过Reset按键切换

1. 切换步骤

长按Reset按键30秒以上，当AP的指示灯绿色4Hz闪烁时松开按键，AP会重启并切换至Cloud模式。

长按Reset按键的时间不同，指示灯状态与含义也不同，具体见下表。

表2-1 Reset按键工作模式切换的指示灯规则表