关于SR8800主控板掉电重启后可能无法启动问题的处理公告
- 0关注
- 1收藏，1079浏览
问题描述：
公告中给出了解决方法是一篇叫《H3C SR8800 产品主控板掉电重启后可能无法正常启动时的处理措施. doc》，就这篇文档
组网及组网描述：
求《H3C SR8800 产品主控板掉电重启后可能无法正常启动时的处理措施. doc》，就这篇文档。
- 2021-05-06提问
- 举报
-
(0)
最佳答案
1
问题确认方法
Boot from primary boot file
Flash file system init........................done.
Can not open flash file: flash:/device.app
FlashToSdram failed!
Boot from backup boot file
Can not open device.app
Rebooting...
Please make sure the baudrate of the terminal is 9600bps!
2
版本启动文件路径丢失的规避方法
可通过bootware/bootroom菜单重新指定版本启动文件的方式，让主控板启动：
2.1 示例：Bootware203版本
Bootware203版本操作如下：
SDRAM init successful.
System is starting...
****************************************************************************
* *
* H
* *
****************************************************************************
Copyright (c) 2004-2010 Hangzhou H
Compiled Date : Apr 27 2010
CPU Type : MPC
CPU L1 Cache : 32KB
CPU L2 Cache : 512KB
CPU Clock Speed : 998MHz
Memory Type : SDRAM
Memory Size : 1024MB
Memory Speed : 133MHz
BootWare Size : 1MB
Flash Size : 64MB
cfa0 Size : 247MB
NVRAM Size : 512KB
CPLD Version : 003
PCB Version : Ver.A
Board self testing...........................
Board steady testing... [ PASS ]
Board SlotNo... [ 0 ]
CPLD1 testing... [ PASS ]
CPLD2 testing... [ PASS ]
The switch's Mac address... [00:
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Please input BootWare password:
Note: The current operating device is cfa0
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Modify BootWare Password |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Enter your choice(0-9): 9 进入存储器操作菜单
==============================<DEVICE CONTROL>==============================
|<1> Display All Available Nonvolatile Storage Device(s) |
|<2> Set The Operating Device |
|<3> Set The Default Boot Device |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 2 设定操作的存储器
Please set the operating device:
============================================================================
|Note:the operating device is cfa0 |
|NO. Device Name File System Total Size Available Space |
|1 flash VFS 66324480 30284800 |
|2 cfa0 FAT 128704512 30226432 |
|0 Exit |
============================================================================
Enter your choice(0-2):2
Set the operation device successful!
==============================<DEVICE CONTROL>==============================
|<1> Display All Available Nonvolatile Storage Device(s) |
|<2> Set The Operating Device |
|<3> Set The Default Boot Device |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 0
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Modify BootWare Password |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Enter your choice(0-9): 4
===============================<File CONTROL>===============================
|Note:the operating device is cfa0 |
|<1> Display All File(s) |
|<2> Set Application File type |
|<3> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 2
'M' = MAIN 'B' = BACKUP 'S' = SECURE 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
|1
98470232 Dec/10/2010 10:50:
|0 Exit |
============================================================================
Enter file No:1
Modify the file attribute:
============================================================================
|<1> +Main |
|<2> -Main |
|<3> +Backup |
|<4> -Backup |
|<0> Exit |
============================================================================
Enter your choice(0-4):1
Set the file attribute success!
===============================<File CONTROL>===============================
|Note:the operating device is cfa0 |
|<1> Display All File(s) |
|<2> Set Application File type |
|<3> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 0
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Modify BootWare Password |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Enter your choice(0-9): 1
Starting to get the main application file--cfa0:/ SR8800-CMW520-R3328-SI.bin!..
............................................................................
2.2 示例：Bootrom109版本
ZBB_TEST
Starting...
***************************************************
* *
* H
* *
***************************************************
Copyright (c) 2004-2008 Hangzhou H
CPU Type : MPC
Memory Size : 1024MB
Board self testing...
The board is steady.
SlotNo of this board is 1.
EPLD1 testing is OK.
EPLD2 testing is OK.
Please check LEDs...Done.
The device's Mac address is 0023.89ca.a200.
Press Ctrl+B to enter Boot Menu... 5
password:
MAIN MENU
1. Boot with default mode
2. Boot from primary boot file
3. Boot from backup boot file
4. Enter serial submenu
5. Enter ethernet submenu
6. Modify boot description area
7. Modify bootrom password
0. Reboot
Enter your choice(0-7): 6
Please input primary boot file name:
Primary Boot File Name = cf:/ SR8800-CMW520-R3238-SI.APP
Please input backup boot file name:
Backup Boot File Name = flash:/ SR8800-CMW520-R3238-SI.APP
MAIN MENU
1. Boot with default mode
2. Boot from primary boot file
3. Boot from backup boot file
4. Enter serial submenu
5. Enter ethernet submenu
6. Modify boot description area
7. Modify bootrom password
0. Reboot
Enter your choice(0-7): 1
- 2021-05-06回答
- 评论(1)
- 举报
-
(0)
感谢大神回复，可是我这个版本并没有您答案中的菜单，我还有什么办法吗？ ZBB_TEST Starting... Warning: Rtc has not been enabled yet, please set the correct time after boot. Failed to init system time! *************************************************** * * * H3C SR8800 Bootrom, Version 109 * * * *************************************************** Copyright (c) 2004-2008 Hangzhou H3C Technologies Co., Ltd. CPU Type : MPC7447A Memory Size : 1024MB Board self testing... The board is steady. SlotNo of this board is 0. EPLD1 testing is OK. EPLD2 testing is OK. 16c2552 register testing is OK. Please check LEDs...Done. The device's Mac address is 000f.e278.2fc9. Data error in boot description area! Save default Boot Description to Boot Description Area... Press Ctrl+B to enter Boot Menu... 4 password: MAIN MENU 1. Boot with default mode 2. Boot from primary boot file 3. Boot from backup boot file 4. Enter serial submenu 5. Enter ethernet submenu 6. Modify boot description area 7. Modify bootrom password 0. Reboot Enter your choice(0-7): 0 Rebooting... Please make sure the baudrate of the terminal is 9600bps! ZBB_TEST Starting... Warning: Rtc has not been enabled yet, please set the correct time after boot. Failed to init system time!
亲~登录后才可以操作哦!
确定你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
- 1. 您举报的内容是什么？（请在邮件中列出您举报的内容和链接地址）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
- 3. 是哪家企业？（营业执照，单位登记证明等证件）
- 4. 您与该企业的关系是？（您是企业法人或被授权人，需提供企业委托授权书）
抄袭了我的内容
×
原文链接或出处
诽谤我
×
- 1. 您举报的内容以及侵犯了您什么权益？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
对根叔社区有害的内容
×
不规范转载
×
举报说明
感谢大神回复，可是我这个版本并没有您答案中的菜单，我还有什么办法吗？ ZBB_TEST Starting... Warning: Rtc has not been enabled yet, please set the correct time after boot. Failed to init system time! *************************************************** * * * H3C SR8800 Bootrom, Version 109 * * * *************************************************** Copyright (c) 2004-2008 Hangzhou H3C Technologies Co., Ltd. CPU Type : MPC7447A Memory Size : 1024MB Board self testing... The board is steady. SlotNo of this board is 0. EPLD1 testing is OK. EPLD2 testing is OK. 16c2552 register testing is OK. Please check LEDs...Done. The device's Mac address is 000f.e278.2fc9. Data error in boot description area! Save default Boot Description to Boot Description Area... Press Ctrl+B to enter Boot Menu... 4 password: MAIN MENU 1. Boot with default mode 2. Boot from primary boot file 3. Boot from backup boot file 4. Enter serial submenu 5. Enter ethernet submenu 6. Modify boot description area 7. Modify bootrom password 0. Reboot Enter your choice(0-7): 0 Rebooting... Please make sure the baudrate of the terminal is 9600bps! ZBB_TEST Starting... Warning: Rtc has not been enabled yet, please set the correct time after boot. Failed to init system time!